| No |
Year |
Code |
Title |
Author(s) |
of Pages |
| 1 |
1960 |
C/1/60 |
Influence de l'anisotropie des toles sur leur deformation plastique en solicitations uni et biaxiales |
C. Crussard; D. Lajeunesse; G. Pomey |
35 |
| 2 |
1960 |
C/2/60 |
Drawability and anisotropy of metals |
R.L. Whiteley; D.E. Wise; D.J. Blickwede |
13 |
| 3 |
1960 |
C/3/60 |
Classification and systemization of sheet metal press forming process |
K. Yoshida |
N/A |
| 4 |
1960 |
C/4/60 |
Le formage des toles minces a froid et les essais d'emboutissage |
J. Guyot |
16 |
| 5 |
1960 |
C/5/60 |
The assessment of the formability of sheet metal by cupping tests and from the stress characteristics |
J.F. Wallace |
15 |
| 6 |
1960 |
C/6/60 |
The new tensile flow-curve for plane strain |
K. Takase |
31 |
| 7 |
1960 |
C/7/60 |
Intersuchung des formziehens komplizierter hohlteile |
A.D. Tomlenow |
10 |
| 8 |
1960 |
C/8/60 |
Evaluation of drawing properties of sheet steel |
L.A. Rubenkova |
10 |
| 9 |
1960 |
C/9/60 |
An investigation of swift cupping test correlation and the influence of tool and material surface finsih on the test results |
P.W. Whitton; D.R. Mear |
24 |
| 10 |
1960 |
C/10/60 |
Investigations on swift cupping test |
J.H. Zaat |
31 |
| 11 |
1960 |
C/11/60 |
The study of strain aging in rimming steel using the swift cupping press and the influence of punch shape on the results |
D.K.C. Ullmann; V.M. Thomas |
18 |
| 12 |
1960 |
C/12/60 |
The usefulness of the tensile and the cup-forming test, when testin aluminum sheet for deep drawing |
C.R. Vassel and G.J. Sinay |
11 |
| 13 |
1960 |
C/13/60 |
A strech-forming test for use with a varaible speed drawing press |
D.V. Wilson; B.B. Moreton; R.D. Butler |
29 |
| 14 |
1960 |
C/14/60 |
Einfluss der werkstoffeigenschaften un prufbedingungen auf die ergebnisse des napfchen-ziehversuchs |
W. Panknin |
24 |
| 15 |
1960 |
C/15/60 |
Influence de quelques facteurs sur les resultats de l'essai erichsen |
M. Jentet |
17 |
| 16 |
1960 |
C/16/60 |
Remarks on the erichsen drawing test |
S. Di Bartolo |
18 |
| 17 |
1960 |
C/17/60 |
Vergleichende untersuchungen uber die erbebnisse der tiefungsprufung mit dem napfchenziehversuch und mit dem erichsen-versuch an weichen stahlen |
A. Kruger |
42 |
| 18 |
1960 |
C/18/60 |
On the correlations among experimental values obtained from various formability tests |
S. Fukui; K. Yoshida; K. Abe |
12 |
| 19 |
1960 |
C/19/60 |
Essai de definition de l'emboutissablilite |
G. Pomey; A. Royez; P. Dhez |
32 |
| 20 |
1960 |
C/20/60 |
Mise au point d'un embouti type representatif des pieces de carrosserie |
M. Jentet |
23 |
| 21 |
1960 |
C/21/60 |
L'essai K.W.I. - Principe et applications aux feuillards pour cages de roulements a billes et a rouleaux |
L. Mazet; M. Vauzelle |
19 |
| 22 |
1960 |
C/22/60 |
La determination des possibilities d'emboutissage cylindrique des alliages legers |
M. R. Chopin |
21 |
| 23 |
1960 |
C/23/60 |
Einfluss der blechdickenabweichungen aus das tiefziehergebnis |
G. Oehler |
11 |
| 24 |
1960 |
C/24/60 |
The problem of elaborating the method of testing to appraise the apacity of sheet steel for deep drawing |
B.M. Ovsy Annikov |
26 |
| 25 |
1960 |
C/25/60 |
Die hydraulische ticfungsprufung zur zufnahme von fliesskurven und zur ermittlung der relativen verfestigung |
W. Panknin |
11 |
| 26 |
1960 |
C/26/60 |
Examen systematique des pieces embouties en feuille mince |
C. Caillot |
15 |
| 27 |
1960 |
C/27/60 |
Formability of sheet metal in successive multistep drawing |
I. Noritzin |
21 |
| 28 |
1960 |
C/28/60 |
Double-action hydroforming process |
S. Fukui; K. Yoshida; K. Abe |
10 |
| 29 |
1960 |
C/29/60 |
The application of phase change lubrication to stretchforming |
J.F. Wallace |
15 |
| 30 |
1960 |
C/30/60 |
Principles and practice of explosive metal forming |
L. Zernow |
4 |
| 31 |
1962 |
C/1/62 |
Speed, lubrication, and surface finish in deep drawing and stretch forming |
J.F. Wallace |
22 |
| 32 |
1962 |
C/2/62 |
The effect of roughness of sheet metal and tool surfaces on deep-drawability |
S. Fukui; K. Yoshida; K. Ozaki |
19 |
| 33 |
1962 |
C/3/62 |
Einfluss der oberflachenrauhigkeit auf der reibungerserscheinungen an tiefziehblechen |
M. Reihle |
11 |
| 34 |
1962 |
C/4/62 |
Problematik des zusammenwirkens von reibungspartnem und gleitmitteln bei der kaltumformung |
H. Wiegand; K.H. Kloos |
39 |
| 35 |
1962 |
C/5/62 |
Plastic strain in stretch-forming of drawing quality cold rolled sheet |
R.H. Heyer; D.E. McCabe |
40 |
| 36 |
1962 |
C/6/62 |
The importance of drawing and fracture loads in the swift cup drawing test |
R.D. Butler; B.B. Moreton; D.V. Wilson |
33 |
| 37 |
1962 |
C/7/62 |
Correlation of laboratory tests on drawing lubricants with press shop practice |
H.T. Coupland |
19 |
| 38 |
1962 |
C/8/62 |
Organic polymers as deep drawing lubricants |
D.R. Mear; H.H. Topper; D.A. Ford |
23 |
| 39 |
1962 |
C/9/62 |
The influence of plastic films on the deep drawing properties of metal sheet |
L. Ameen |
25 |
| 40 |
1962 |
C/10/62 |
Kalt - und warmumformung unter schlagziehpressen |
G. Oehler |
14 |
| 41 |
1962 |
C/11/62 |
L'echauffement du metal en cours d'emboutissage-restreint |
A. Finckbohner; J. Guyot |
9 |
| 42 |
1962 |
C/12/62 |
Die unformung von blechen mit sprengstoffen |
P.J.M. Boes |
23 |
| 43 |
1962 |
C/13/62 |
Fundamental studies on explosive metal forming |
S. Fukui; K. Kawata; J. Seino |
11 |
| 44 |
1962 |
C/14/62 |
Grundsatzliche untersuchungen zur sprengverformung |
H. Hansel |
12 |
| 45 |
1962 |
C/15/62 |
Explosive deformation in anisotropic materials with special reference to mechanical properties |
C.A. Verbraak |
14 |
| 46 |
1962 |
C/16/62 |
Experiments in the dynamic deformation of clamped circular sheets of various metals subject to an underwater explosive charge |
F.W. Travis; W. Johnson |
26 |
| 47 |
1964 |
C/1/64 |
Influence of crystallographic orientation on plastic anisotropy in deep drawing sheet steel |
R.W. Vieth; R.L. Whitely |
20 |
| 48 |
1964 |
C/2/64 |
The theoretical analysis of r value effects on L.D.R. with the application of width reduction |
T. Ikeshima; M. Fukuda |
20 |
| 49 |
1964 |
C/3/64 |
The effect of anisotropy on instability in sheet metal forming |
G. G. Moore; J.F. Wallace |
15 |
| 50 |
1964 |
C/4/64 |
An evaluation of anisotropy for drawability control by plane-strain compression testing |
R.T. Holcomb; W.A. Backofen |
16 |
| 51 |
1964 |
C/5/64 |
La classification des qualities de toles pour emboutissage sur la base des mesures des coefficients d'anisotropie plastique 'r' et module d'ecrouissage 'n' |
L. Lilet |
22 |
| 52 |
1964 |
C/6/64 |
Anisotropy as a criterion in the raming deep drawing test |
G. Oehler |
4 |
| 53 |
1964 |
C/7/64 |
The measurement of plastic anisotropy in sheet steel |
M. Atkinson; I.M. Maclean |
20 |
| 54 |
1964 |
C/8/64 |
Role de quelques facteurs intervenant dans la mesure de 'r' et de 'n' |
M. Grumbach; G. Pomey |
39 |
| 55 |
1964 |
C/9/64 |
Studies on tensile test specimens and a new recording apparatus for sheet metals |
S. Fukui; K. Yoshida; Tensile Test Research Group |
13 |
| 56 |
1964 |
C/10/64 |
Les informations que donne l'essai de traction sur l'aptitude a l'emboutissage de l'acier sont elles applicables a d'autres metaux? |
M. Wybo |
15 |
| 57 |
1964 |
C/11/64 |
An investigation into the relationship between plastic strain ratio and annealing textures in aluminum/magnesium alloy sheets |
R. Pearce; K.R. Natarajan |
23 |
| 58 |
1964 |
C/12/64 |
Influence d'elements d'addition et de traitements speciaux sur l'anisotropie et l'embouteissabilitie d'aciers effervescents extra - doux |
P. Wacquez; R. Van Daele |
23 |
| 59 |
1964 |
C/13/64 |
The effect of manufacturing processes on the preferred orientation of deep drawing steel sheet |
H. Yoshida; K. Sasaki; F. Kanzaki |
14 |
| 60 |
1966 |
C/1/66 |
Evaluation of drawability |
D.L Harper; R.L. Whitely |
29 |
| 61 |
1966 |
C/2/66 |
The efficiency of deformation as a measure for drawability of sheet metals |
M. Abouel - ALA |
17 |
| 62 |
1966 |
C/3/66 |
A study of rectangular shell drawing for sheet metal testing |
H.T. Coupland; R.R. Arnold |
10 |
| 63 |
1966 |
C/4/66 |
The influence of tool dimensions on the results of the swift cupping test |
H. De Goede; S. Von Marinelli |
31 |
| 64 |
1966 |
C/5/66 |
L'effet dimensionnel dans les essais d'emboutissage profond |
M. Wybo |
19 |
| 65 |
1966 |
C/6/66 |
Etude des modes de deformation en emboutissage. Cas particulier des pieces de carrosserie d'automobile |
H. Josselin |
33 |
| 66 |
1966 |
C/7/66 |
Contribution a l'etude de l'emboutissage sous presse |
G. Pomey; M. Grumbach; R. Guillot |
44 |
| 67 |
1966 |
C/8/66 |
The study on wall breakage in the deep-drawing of square shells |
T. Okamoto; V. Hayashi |
22 |
| 68 |
1966 |
C/9/66 |
Material requirements for forming a rectangular pan |
R.H. Heyer; J.R. Newby |
29 |
| 69 |
1966 |
C/10/66 |
The study and classification of punch-stretching processes |
K. Yoshida; K. Miyauchi |
35 |
| 70 |
1966 |
C/11/66 |
Effect of mechanical properties of sheet steel on the springback of press-formed parts |
T. Akamatsu; S. Yanagimoto; I. Aoki; S. Hanai |
19 |
| 71 |
1966 |
C/12/66 |
Stretch-expand forming |
S. Fukui; K. Yoshida; K. Abe |
19 |
| 72 |
1966 |
C/13/66 |
Das hydromechanische Ziehverfahren |
O.E. Burk |
16 |
| 73 |
1966 |
C/14/66 |
Procede de formage a l'explosif dans l'emploi des toles minces. Le placage des metaux a l'explosif |
E. Perrin |
21 |
| 74 |
1966 |
C/15/66 |
An experimental investigation on the propagation of strain waves in a blank at high-energy-rate forming |
K. Kiyota; M. Fujita |
28 |
| 75 |
1966 |
C/16/66 |
Le mecanisme du formage et du placage des metaux a l'explosif |
J. Pietteur |
48 |
| 76 |
1968 |
C/1/68 |
Variation de l'allongement local de rupture en expansion des toles minces en fonction de la biaxialite de la deformation |
L. De Lacombe; C. Dumenil |
10 |
| 77 |
1968 |
C/2/68 |
Initiation and propagation of fracture during biaxial stretching of steel sheets |
H. Takechi; Y. Matsuo; S. Nagashima |
11 |
| 78 |
1968 |
C/3/68 |
Ductile Fracture of commercial carbon steel sheets in tensile testing |
K. Nakagawa |
12 |
| 79 |
1968 |
C/4/68 |
Ductile fracture strain of steel sheet by hydraulic bulge test |
T. Okamoto; T. Matsouka; Y. Hayashi; C. Sudo |
5 |
| 80 |
1968 |
C/5/68 |
Instability and fracture behaviours in steel metal forming |
K. Yoshida; K. Abe; K. Miyauchi; T. Nakagawa |
15 |
| 81 |
1968 |
C/6/68 |
Analysis of necking preceding fracture of sheet metal under tension |
Z. Marciniak |
9 |
| 82 |
1968 |
C/7/68 |
On the accuracy of likeness between Vee-bend tool and bent component and how to influence it by a setting load |
E. Dannenmann |
16 |
| 83 |
1968 |
C/8/68 |
The effect of plastic anisotropy on flange wrinkling behaviour during sheet metal forming |
H. Naziri; R. Pearce |
8 |
| 84 |
1968 |
C/9/68 |
Preliminary experiments on the multi-stage deep drawing of high speed steel and a low tungsten tool steel |
B. Fogg; P.F. Thomason |
7 |
| 85 |
1968 |
C/10/68 |
Investigation into the deep drawing with particular consideration of simulataneous ironing |
Y. Kasuga; I. Otoda; R. Sugiyama |
11 |
| 86 |
1968 |
C/11/68 |
Relation between the manufacturing conditions and the average strain according to the scribed circle tests in steel sheets |
K. Takashina; T. Herai, H. Komorida; T. Horita |
9 |
| 87 |
1968 |
C/12/68 |
Application of strain analysis to sheet metal forming problems in the press shop |
G.M. Goodwin |
8 |
| 88 |
1968 |
C/13/68 |
Sur la determinationdes coefficients 'r' et 'n' |
C. Schneider |
7 |
| 89 |
1968 |
C/14/68 |
The influence of the strain hardening properties on the different judgement of the deep drawability in the swift cup drawing test and Engelhardt cup drawing test |
C. Weidemann |
8 |
| 90 |
1968 |
C/15/68 |
A new approach for predicting the limiting drawing ratio |
P.B. Mellor; J. Chakrabarty |
9 |
| 91 |
1968 |
C/16/68 |
A Comparative study of different deep drawing test methods |
H. De Goede; S.V. Marinelli |
5 |
| 92 |
1970 |
C/1/70 |
U Type Stretch Flanging |
T. Matsuoka; C. Sudo; M. Kojima |
5 |
| 93 |
1970 |
C/2/70 |
Improvement in the Deformability of Sheared Edge of Steel Sheets |
T. Nakagawa; K. Yoshida |
6 |
| 94 |
1970 |
C/3/70 |
The Curve of Formability Limit and Its Application to a Difficult Drawing Operation |
J.C. Baret; M. Wybo |
4 |
| 95 |
1970 |
C/4/70 |
The Effect of r and n upon the Forming Limit Diagrams of Sheet Steel |
J. Woodthorpe; R. Pearce |
6 |
| 96 |
1970 |
C/5/70 |
Effect of Deforming conditions and Mechanical Properties on the Stretch Forming Limits of Steel Sheets |
T. Kikuma; K. Nakazima |
5 |
| 97 |
1970 |
C/6/70 |
Prediction of the Forming limit in Steel Sheet Stamping |
H. Kubotera; Y. Ueno |
5 |
| 98 |
1970 |
C/7/70 |
Deformation Analysis in Press Forming of Autobody Parts |
T. Kobayashi; K. Murata; H. Ishigaki; T. Abe; R. Mio |
5 |
| 99 |
1970 |
C/8/70 |
Relations between Deforming Behaviours and Geometrical Factors of Autobody Parts in Press Forming |
T. Kobayashi; K. Murata; H. Ishigaki; T. Abe; R. Mio |
5 |
| 100 |
1970 |
C/9/70 |
Research of Criteria in Sheet Forming Applicable to the Automotive Industry |
H. Josselin; M. Tong-Cuong; R. El. Haik |
3 |
| 101 |
1970 |
C/10/70 |
Metallurgical Aspects of Sheet Steel for Press Shops |
R.D. Butler; D. North; G.M. Davies |
9 |
| 102 |
1970 |
C/11/70 |
The Stability of Performance in Press Forming Operations |
K. Yoshida; K. Yoshii |
7 |
| 103 |
1970 |
C/12/70 |
Prediction of Ironability in Forming Cylindrical Shells by Deep Drawing and Multi-Stage Ironing |
K. Takase; Y. Kurita |
6 |
| 104 |
1970 |
C/13/70 |
Formation Mechanicsms of Annealing textures in Low carbon Steel Sheets |
M. Matsuo; S. Hayami; S. Nagashima |
5 |
| 105 |
1970 |
C/14/70 |
On Rolling and Annealing Textures in Low Carbon Steel Sheets |
G. Pomey; M. Grumbach |
6 |
| 106 |
1970 |
C/15/70 |
The Control of Grain Size and Orientation in Sheet Steel |
I.L. Dillamore and W.B. Hutchinson |
7 |
| 107 |
1970 |
C/16/70 |
Strain Hardening in Austenitic Steels |
P. Lovland; G. Molinder |
4 |
| 108 |
1970 |
C/17/70 |
Deformation Markings in 17% Chromium Stainless Steels |
T.R. Thomson; J.M. Baker |
3 |
| 109 |
1970 |
C/18/70 |
On the Ridging Properties and the Textures of 17% Cr Stainless Steel Strip Cold-rolled and Annealed from Continuously Cast Slab |
M. Arakawa; S. Takemura; T. Ooka |
5 |
| 110 |
1970 |
C/19/70 |
Application of Finite Element Method and Moire Techniue to Sheet Metal Forming Problems |
S. Hanai; I. Aoki; T. Horita; H. Komorida; ; Y. Nishimoto |
3 |
| 111 |
1970 |
C/20/70 |
A Theoretical Analysis of the Influence of Normal Anisotropy 'r', and Strain Hardening Exponent 'n', on the Drawability of Sheet Steel |
K.M. Frommann; W.F. Barclay |
6 |
| 112 |
1970 |
C/21/70 |
The Kinematics of Axisymmetrical Sheet Metal Forming Processes and the Definition of Drawability |
T.C. Hsu |
5 |
| 113 |
1970 |
C/22/70 |
The Coefficient of Friction on the Round Headed Punch in Press Forming |
K. Nakagawa; S. Okazaki |
3 |
| 114 |
1970 |
C/23/70 |
Metallurgical Factors Influencing Sheet Metal Formability |
V.P. Sardana |
6 |
| 115 |
1970 |
C/24/70 |
Aging of Unalloyed Soft Steels |
F. E. Listhuber |
7 |
| 116 |
1970 |
C/25/70 |
Process Variables Affecting the r-value of Cold Rolled Steel Sheet |
K. Yamada; H. Kubotera; K. Nakoka |
5 |
| 117 |
1970 |
C/26/70 |
Properties of Thinner Hot Rolled Steel Strips |
T. Okamoto; K. Nishizawa; H. Okabe; M. Takahashi |
5 |
| 118 |
1970 |
C/27/70 |
Stainless Steel Sheet Cladding on Geometrically Non-Uniform Base Plate by Exlplosive Method |
H.S. Choi; K.T.Chang |
6 |
| 119 |
1970 |
C/28/70 |
Yield Loci for Prestrained Steel Sheets |
Y. Tozawa; M. Nakamura; I. Shinkai |
5 |
| 120 |
1970 |
C/29/70 |
An Analog Computer Used to Evaluate the Tensile Properties of Drawing Quality Sheets |
L. Renard; Ch. Van Den Hove; M. Wyybo |
4 |
| 121 |
1970 |
C/30/70 |
Analysis of the Conical Cup Test for the Assessment of Deep Drawability |
G.S.A. Shawki |
7 |
| 122 |
1970 |
C/31/70 |
The Relation between Lubrication and r Value in Mild Steel Sheets |
K. Suzki; N. Ogoshi; I. Gokyu |
3 |
| 123 |
1970 |
C/32/70 |
A New Test for the Assessment of Normal anisotropy in Sheet Steel |
W.F. Barclay; K.M. Frommann |
4 |
| 124 |
1970 |
C/33/70 |
Effect of Plastic Anisotropy on the Bore Expanding Behaviours of cold Rolled Steel Sheets |
Y. Ito; K. Hasiguchi; N. Ohashi |
5 |
| 125 |
1970 |
C/34/70 |
The Effect of r-Value on the Drawability of Sheet Metal |
T. Oki; M. Miyahara; Y. Yamauchi; I. Kokubo; H. Hirano |
4 |
| 126 |
1970 |
C/35/70 |
On the Interpretation of the Formability Limits of Metal Sheets and Their Evaluation by Means of Elementary Tests |
P. Brozzo; B. Deluca |
3 |
| 127 |
1970 |
C/36/70 |
Introduction of Stress Ratio into Stress-Strain Relation and Its Application to the Development of a New Aspect in Formability |
K. Yoshida; K. Abe; K. Miyauchi; K. Yoshi |
5 |
| 128 |
1972 |
C/1/72 |
Instability and fracture in sheet metal |
M.J. Painter; R. Pearce |
24 |
| 129 |
1972 |
C2/72 |
Prediction of the limiting drawing ratio in the deep-drawing of a flatheaded cylindrical shell |
M.G El-Sebaie; P.B. Mellor |
13 |
| 130 |
1972 |
C/3/72 |
A new method for the prediction of the formability limits of metal sheets |
P. Brozzo; B. De Luca; R. Redina |
28 |
| 131 |
1972 |
C/4/72 |
Influences des grilles de mesure et des trajectoires de deformation sur les courbes limites d'emboutissage |
M. Grumbach; G. Sanz |
27 |
| 132 |
1972 |
C/5/72 |
A simple forming limit curve technique and results on aluminum alloys |
S.S. Hecker |
37 |
| 133 |
1972 |
C/6/72 |
Assessment of sheet metal failure sensitivity by method of torsioning the rings |
Z. Marciniak; J. Kolodziejski |
8 |
| 134 |
1972 |
C/7/72 |
Some strain-rate effects on planar stress systems in Al-stabilized and mechanically capped mild steels |
J.A. Smedstam |
13 |
| 135 |
1972 |
C/8/72 |
Effect to strain ratios on the deforming limit of steel sheet and its application to actual press forming |
T. Kobayashi; H. Ishigaki; T. Abe |
26 |
| 136 |
1972 |
C/9/72 |
Fracture behaviour, forming severity and metal flow in deep drawing of irregular-shaped shells |
K. Yoshida; K. Yoshii; H. Komorida; K. Myauchi |
31 |
| 137 |
1972 |
C/10/72 |
Einflusse auf den Verfestigungsexponenten (n-Wert) von Tiefziehblech und ihre Deutung |
V.U. Lotter; M. Muller; W. Muschenborn; P.L. Ryder |
16 |
| 138 |
1972 |
C/11/72 |
New forming grade sheet steels |
R. Hobbs; T.R. Thomson; I.S. Brammar |
22 |
| 139 |
1972 |
C/12/72 |
The influence of yield strength and steel cleanness on the formability of hot rolled strip |
R.F. Dewsnap; R. Pearce; J.R. Branson |
30 |
| 140 |
1972 |
C/13/72 |
Auswirkungen der Werkzeuggeometrie und der Werkstoffkennwerte auf den spannungs und Formanderungszustand beim Ziehen von Blechstreifen in einem Modellwerzeug |
?? |
25 |
| 141 |
1972 |
C/14/72 |
Drawing and ironing of tinplate |
C.H. Schneider; M. Sodeik; H.U. Weigel |
19 |
| 142 |
1972 |
C/15/72 |
Les courbes limites de formage Application a l'emboutissage de pieces automobiles |
G. Fourdin; H. Josselin; R. El Haik |
12 |
| 143 |
1972 |
C/16/72 |
The study on press formability in forming of autmotive panels |
Y. Hayastri; C. Sudo; M. Kojima |
35 |
| 144 |
1972 |
C/17/72 |
Stretch-draw shape analysis for prediction of formability |
A.S. Kasper; P.J. Vanderveen |
19 |
| 145 |
1972 |
C/18/72 |
Analysis of sheet metal formability |
AMERICAN DEEP DRAWING RESEARCH GROUP |
26 |
| 146 |
1972 |
C/19/72 |
The determination and application of the FLC-onset of localised necking |
C.CHR. Veerman |
29 |
| 147 |
1974 |
C/1/74 |
On the strain hardening index n |
Y. Bergstrom |
23 |
| 148 |
1974 |
C/2/74 |
The effect of strain rate on the stress-strain curve and the plane anisotropy coefficient of unstable and stable austenitic stainless steels |
K.J. Blom; G. Brandt; L. Klang |
21 |
| 149 |
1974 |
C/3/74 |
On the quantitative evaluation of plastic anisotropy in sheet metals |
W. Truszkowski |
14 |
| 150 |
1974 |
C/4/74 |
Quantitative study of the relationship between the strain ratio (r-value), earing and the texture of thin sheets of low carbon steel |
M. Grumbach; P. Parniere; L. Roesch; C. Sauzay |
15 |
| 151 |
1974 |
C/5/74 |
A criterion for plastic instability in punch stretching of thin sheets |
A.K. Ghosh; S.S. Hecker |
15 |
| 152 |
1974 |
C/6/74 |
Mechanical and metallurgical properties related to hot and cold rolled high strength sheet steels |
S. Hanai; S. Sakai; T. Sakamoto; T. Satoh; I. Aoki |
14 |
| 153 |
1974 |
C/7/74 |
Formability of high-strength low-alloy steels |
M.J. Painter; R. Pearce |
14 |
| 154 |
1974 |
C/8/74 |
High resistant steels and their formability x |
ITALIAN DEEP DRAWING RESEARCH GROUP |
N/A |
| 155 |
1974 |
C/9/74 |
An Investigation on the stamping of high strength sheet steel |
M. Nakano; O. Kinpara |
13 |
| 156 |
1974 |
C/10/74 |
Inclusions, strength and formability |
N.A. Cantalejos; R.F. Dewsnap; R.A. Maynard |
14 |
| 157 |
1974 |
C/11/74 |
The influence of sulphur content on the formability of HSLA sheet steels |
G. Glover |
16 |
| 158 |
1974 |
C/12/74 |
Mikrolegierte bandverzinkte Feinblechguten mit guter kaltumformbarkeit |
C. Vlad; H. Klimpel ***DISTRIBUTED SEPARATELY BY THE AUTHOR |
14 |
| 159 |
1974 |
C/13/74 |
Prediction of strain distribution on formed sheet metal parts |
THE BENELUX DEEP DRAWING RESEARCH GROUP |
13 |
| 160 |
1974 |
C/14/74 |
Some investigations on elastic recovery of press formed parts of high strength steel sheets |
C. Sudo; M. Kojima; T. Matsuoka |
13 |
| 161 |
1974 |
C/15/74 |
The assessment of sheet steel forming severity in autobody stamping |
S. Hanai; S. Sakai; I. Aoki; T. Satoh; T. Horita |
14 |
| 162 |
1974 |
C/16/74 |
Comparison of various plastic instability criteria for sheet metal forming applications |
B. Kaftanoglu |
13 |
| 163 |
1974 |
C/17/74 |
Determination des efforts developes au cours du pliage des toles minces |
Bouhelier; Deagas; Martin |
28 |
| 164 |
1974 |
C/18/74 |
The effects of mechanical properties of sheet metals on the growth and removing of buckles due to non-uniform stretching |
K. Yoshida; H. Hayashi; K. Miyauchi; Y. Yamamoto; K. Abe |
11 |
| 165 |
1974 |
C/19/74 |
Some practical aspects of pressing and deep drawing using high strength hot rolled steels |
A. Stanway; W. Holyman |
18 |
| 166 |
1974 |
C/20/74 |
Better sheet metal utilization - Trends in Benelux |
THE BENELUX DEEP DRAWING RESEARCH GROUP |
17 |
| 167 |
1974 |
C/21/74 |
Improvements of press performance for autobody press shops in tool and process aspects |
T. Asi; H. Kozawa; K. Kato; K. Iso |
8 |
| 168 |
1974 |
C/22/74 |
Pressworking Economics |
J. R. Branson |
15 |
| 169 |
1976 |
C/1/76 |
Use of high yield strength steels to reduce weight of motor cars while keeping same safety level |
Busson; Chevrier; Entringer; De Kainlis - France |
12 |
| 170 |
1976 |
C/2/76 |
High-strength cold-rolled sheet: Characteristics and criteria for its use in autmobile manufacturing |
W. Muschenborn; K. Blumel; L. Meyer; C. Strassburger |
26 |
| 171 |
1976 |
C/3/76 |
Development and features of continuously annealed high strength cold rolled sheet steels in Japan |
K. Araki; K. Nakaoka; M. Abe; N. Ohashi (Japan) |
15 |
| 172 |
1976 |
C/4/76 |
Car body made from galvanized steel sheet |
H. Burst; M. Grahle; J. Grashoff; C. Schneider; COLLABORATORS |
13 |
| 173 |
1976 |
C/5/76 |
Method for prediction of cold deformation textures |
P. Van Houtte; E. Aernoudt |
14 |
| 174 |
1976 |
C6/76 |
The effect of anisotropic plasticity and work-hardening on the sheet metal drawability |
J. Gronostajski; C. Banasiak |
16 |
| 175 |
1976 |
C/7/76 |
Anit-galling roughness profile permitting reduction of the blankholder pressure and required amount of lubricant during the forming of sheets |
D. Rault; M. Entringer |
18 |
| 176 |
1976 |
C/8/76 |
A new plastic instability criteria for sheet metal forming applications |
A. Rauter; J. Reissner (Switzerland) |
16 |
| 177 |
1976 |
C/9/76 |
Bulge testing as an aid to formability assessment |
J. L. Duncan; J. Kolodziejski; G. Glover |
20 |
| 178 |
1976 |
C/10/76 |
The strain propagation behaviour in a metal sheet under non-uniformity distributed stretching load |
K. Yoshida; H. Takechi; S. Kuriyama; H. Hayashi (Japan) |
16 |
| 179 |
1976 |
C/11/76 |
The influence of strain-path changes on the formability of sheet steel |
A.K. Ghosh; J.V. Laukonis (USA) |
12 |
| 180 |
1976 |
C/12/76 |
Sheet bending in elastic tools |
R. Crafoord (Sweden) |
14 |
| 181 |
1976 |
C/13/76 |
On the interpretation of results of hole expansion tests on sheet steels |
M. De Groot (Netherlands) |
14 |
| 182 |
1976 |
C/14/76 |
Effectiveness of flange holding on the die surface with draw beads |
M. Kojima; C. Sudo; Y. Hayashi |
13 |
| 183 |
1976 |
C/15/76 |
How to characterize the formability of thin sheets - Influence of the tooling on the formability of tin and black plates |
R. D'Haeyer; J. Gouzou; A. Bragard (Belgium) |
15 |
| 184 |
1976 |
C/16/76 |
Application of sheet metal research to high production fabrication shops |
W.E. Johnson; P.A. Stine (USA) |
10 |
| 185 |
1976 |
C/17/76 |
The effect of mechanical properties of sheet metals on the wrinkling behaviour during deep drawing |
J. Havranek (Australia) |
19 |
| 186 |
1976 |
C/18/76 |
Strain rate and temperature sensitivity of austenitic stainless steel sheet formability |
R. Jackson (Australia) |
21 |
| 187 |
1978 |
C/1/78 |
Flange behaviour analysis in sheet metal forming of complex geometry |
K. Yoshida; K. Miyauchi; H. Hayashi; S. Kuriyana (Japan) |
27 |
| 188 |
1978 |
C/2/78 |
Plastic flow of axisymmetric shells and its application to sheet metal forming process |
O.C. Zienkiewicz; E. Onate |
10 |
| 189 |
1978 |
C/3/78 |
Press performance, forming geometry and fracture behaviour in actual autobody panels |
T. Furubayshi, M. Shiokawa; K. Yamazaki (Japan) |
6 |
| 190 |
1978 |
C/4/78 |
Approximate calculations for draw die forming |
J. L. Duncan (Canada) |
8 |
| 191 |
1978 |
C/5/78 |
Analysis of surface deformation defects in the press forming of large sized autobody panels |
H. Ishigaki; Y. Umehara; I. Okamoto |
14 |
| 192 |
1978 |
C/6/78 |
An investigation into the pressing of ridges into flat panels |
I. Adak; F.W. Travis (Great Britain) |
11 |
| 193 |
1978 |
C/7/78 |
The blankholding action of draw beads |
C. Weidemann (Sweden) |
7 |
| 194 |
1978 |
C/8/78 |
The study on resistance against wall breakage of metal sheets |
Y. Hayashi (Japan) |
8 |
| 195 |
1978 |
C/9/78 |
Deformation behaviour of thin diaphragms in static and dynamic punch-stretching |
S.K. Ghosh; F.W. Travis |
17 |
| 196 |
1978 |
C/10/78 |
Press Formability of damping sheets |
Y. Yutori; S. Nomura; I. Kokubo |
7 |
| 197 |
1978 |
C/11/78 |
Sheet metal forming - transferring technology to the shop floor |
R. Hobbs; J. Havranek; I.S. Brammar (Australia) |
6 |
| 198 |
1978 |
C/12/78 |
The effect of tooling temperature on the formability of low carbon steel sheets |
W.G. Granzow (USA) |
6 |
| 199 |
1978 |
C/13/78 |
Theoretical analysis of the influence of damage on the shape and position of the forming limit diagram and on the strain-path and thickness effects |
J.M. Jalinier; B. Baudelet (France) |
10 |
| 200 |
1978 |
C/14/78 |
Evolution of the microscopal heterogenities in sheet metal forming |
M.C. De Souza Nobrega; H.L. De Andrale; E.C. Sarmento; G. Ferran (Brazil) |
9 |
| 201 |
1978 |
C/15/78 |
Effects of microstructure on formability in biaxial stretching |
O. Asceinrad; D.V.Wilson (Great Britain) |
12 |
| 202 |
1978 |
C/16/78 |
The uniaxial strain-hardening behaviour of sheet metal from zero strain to failure |
K. Saka; M.J. Painter; R. Pearce (Great Britain) |
12 |
| 203 |
1978 |
C/17/78 |
Effect of strain rate and deformation heating on the strain-hardening of sheet metals |
H.J. Kleemola; A.S. Korhonen; A.J. Ranta-Eskola (Finland) |
4 |
| 204 |
1978 |
C/18/78 |
Strain rate sensitivity, workhardening rate and strain prior to localized necking during tensile testing in some aluminum alloys |
H. Hero |
8 |
| 205 |
1978 |
C/19/78 |
Strain and strain-rate hardening effects on punch stretching of 5182-0 aluminum at elevated temperatures |
R.A. Ayres; M.L. Wenner (USA) |
6 |
| 206 |
1978 |
C/20/78 |
Material properties controlling the strain distribution of sheet metal |
W. Muschenborn; H.M. Sonne (W. Germany) |
9 |
| 207 |
1978 |
C/21/78 |
Influence of deformation path upon the change of plastic anisotropy during the forming of hot and cold rolled low carbon deep drawing sheet steel |
D. Grzesik; C.M. Vlad (W. Germany) |
8 |
| 208 |
1978 |
C/22/78 |
Age-hardenable, low yield-high tensile strength sheet steels for automobiles |
M. Nishida; I. Takahashi; K. Hasiguchi; T. Kato; T. Tanaka (Japan) |
9 |
| 209 |
1978 |
C/23/78 |
Assessment of shape fixability and stretchability in CAPL dual phase steel sheets |
H. Takachi; M. Usuda (Japan) |
9 |
| 210 |
1978 |
C/24/78 |
Influence de la structure de refroidissement des lingots sur le cordage des feuillards en acier ferritique au chrome du type AISI 430 |
J. Heritier (France) |
13 |
| 211 |
1978 |
C/25/78 |
Influence of steel sheet topography on the deep drawing process |
C. Weidemann (Sweden) |
7 |
| 212 |
1978 |
C/26/78 |
Present state of the CRM work related to surface analysis of cold-rolled steel sheets |
C.R.M. Liege (Belgium) |
26 |
| 213 |
1978 |
C/27/78 |
The effects of ION implantation into mild steel sheets |
K. Yoshida; T. Stato; H. Hayashi; M. Iwaki; H. Ike (Japan) |
7 |
| 214 |
1978 |
C/28/78 |
Galling behaviour and its tests in press forming of autobody parts |
The Japan Sheet Metal Forming Research Group |
10 |
| 215 |
1978 |
C/29/78 |
Surface interactions during pressforming as simulated by the strip draw test |
K. Blumel (Germany) |
5 |
| 216 |
1978 |
C/30/78 |
The role of lubrication in the forming of a cylindrical cup |
A. Ferron (France) |
14 |
| 217 |
1978 |
C/31/78 |
Biaxial stress testing of ultra fine grain aluminum alloy sheet |
B.D. McLaughlan; J.L. Duncan (Canada) |
8 |
| 218 |
1978 |
C/32/78 |
Prediction of punched surface stretch flangeability of punched surface steel sheets |
K. Matsudo; K. Osawa; M. Yoshida (Japan) |
10 |
| 219 |
1978 |
C/33/78 |
Surface and galling characteristics of a series of high strength cold-rolled steels |
R.R. Hilsen; I.F. Hughes; D.T. Quinto |
20 |
| 220 |
1978 |
C/34/78 |
The sheet metal forming process, 1958-1978 |
P.B. Mellor |
25 |
| 221 |
1980 |
C/1/80 |
Twenty years of the IDDRG's history |
C. Crussard |
10 |
| 222 |
1980 |
C/2/80 |
On physical meaning of the stress-strain relationship parameters in high strength polycrystalline metals |
W. Truszkowski |
9 |
| 223 |
1980 |
C/3/80 |
HSLA steels. Characteristics for the utilization in forming processes |
R. Coutin; J.P. Doche; A. Ferron; J. Michel |
11 |
| 224 |
1980 |
C/4/80 |
Factors determining the energy absorption of high strength steel |
K.W. Blumel; W. Muschenborn |
12 |
| 225 |
1980 |
C/5/80 |
Problems of high strength steel sheets for autobody parts |
S. Sato; M. Shiokawa; T. Furubayashi; K. Yamazki |
10 |
| 226 |
1980 |
C/6/80 |
Required properties of high strength steel sheets for autobody parts |
S. Sato; M. Shiokawa; T. Furubayahsi; K. Yamazaki |
10 |
| 227 |
1980 |
C/7/80 |
Analysis of shap fixability in high tensile strength steel sheets in press forming |
Y. Umehara |
10 |
| 228 |
1980 |
C/8/80 |
Study for the use of high strength steel sheet for autobody panels |
T. Asai; K. Sakai; K. Kato; A. Oohashi; M. Hirano |
10 |
| 229 |
1980 |
C/9/80 |
Spot welding of high strength steel sheets for deep drawing |
J. Defourny; R. D'Haeyer; A. Bragard; J. Dawance; A. Mertens; L. Renard |
14 |
| 230 |
1980 |
C/10/80 |
Properties of formed parts: flow and fracture behaviour after cold forming in HSLA steel sheets |
P.L. Charpentier; H. R. Piehler |
12 |
| 231 |
1980 |
C/11/80 |
Effect of the inclusions content on damage generation during sheet metal forming of low carbon steel |
C. Souza-Nobrega; B. Fidelis Da Silva; G. Ferran; J.M. Jalinier; B. Baudelet |
10 |
| 232 |
1980 |
C/12/80 |
The development of thickness non-uniformities leading to failure in sheet metals |
P.F. Thomson; P.U. Nayak |
10 |
| 233 |
1980 |
C/13/80 |
Different damage behaviours and their influence on forming process |
J.M. Jalinier; J.H. Schmitt; R. Argemi; J.L. Salsmann; B. Baudelet |
14 |
| 234 |
1980 |
C/14/80 |
Calculation of the damage behaviour during stretch forming. Case of a cylindrical multipasses deep drawn box |
L. Felgeres |
14 |
| 235 |
1980 |
C/15/80 |
Deep drawing of coil coated steel sheet |
Ch. Weidemann |
10 |
| 236 |
1980 |
C/16/80 |
Behaviour of coated film in pressforming of surface treated steel sheet |
C. Sudoo; Y. Hayahsi; M. Nishihara |
10 |
| 237 |
1980 |
C/17/80 |
Deep Drawing and ironing of steel sheet |
H. Khademy-Zadeh; H.T. Coupland; P.B. Mellor |
9 |
| 238 |
1980 |
C/18/80 |
Forming of aluminum alloys for autobody components |
K. Lange; M. Blaich |
10 |
| 239 |
1980 |
C/19/80 |
Formability of aluminum alloys for deep and stretch forming parts |
H.P. Falkenstein |
7 |
| 240 |
1980 |
C/20/80 |
Plastic instability in stretchforming of AlZnMg alloys |
B. Anderson |
5 |
| 241 |
1980 |
C/21/80 |
A fully annealed AlMGAn alloy, free of stretcher strain marks and of stress corrosion |
R. Akeret |
6 |
| 242 |
1980 |
C/22/80 |
Factors influencing the forming limits of sheet metals |
H. Kleemola; J.O. Kumpulainen; A. Ranta-Eskola |
10 |
| 243 |
1980 |
C/23/80 |
The formability of steel sheets ot moderately elevated temperatures |
N.K. Wong; B.H. Arkun; W.T. Roberts; D.V. Wilson |
10 |
| 244 |
1980 |
C/24/80 |
Fittability of metal sheets in sheet metal forming |
K. Yoshida; K. Miyauchi; H. Hayashi; H. Ishigaki; T. Furubayashi |
10 |
| 245 |
1980 |
C/25/80 |
High strength cold rolled low carbon steel sheets |
J.R. Newby; R.E. Hook; J.W. Young |
17 |
| 246 |
1980 |
C/26/80 |
Dual Phase steels. Production and formability |
T.R. Thomson, R.M. Hobbs |
10 |
| 247 |
1980 |
C/27/80 |
Formability of high strength cold rolled steel sheets with 400 Mpa tensile strength |
T. Shimomura; M. Yoshida; M. Sakoh; K. Matsudo |
10 |
| 248 |
1980 |
C/28/80 |
Press formability of high strength cold rolled steel sheets |
K. Nakagawa; H. Abe |
10 |
| 249 |
1980 |
C/29/80 |
Vacuum alloyed and decarburized HSLA steels (SH VAD). FLC obtained in industrial pressing of styled car wheel discs |
G. Arrigoni; M. Palladino; G. Volpato; S. Gubian |
9 |
| 250 |
1980 |
C/30/80 |
Predictions of drawability limits, including the proneness to wrinkling. Actual experience of a mathematical model for deep-drawing |
C. Marique; R. D'Haeyer; J. Mignon; J. Gouzou; A. Bragard |
11 |
| 251 |
1980 |
C/31/80 |
Calculation of the maximum drawing ratio obtainable in deep drawing without a blankholder |
J.O. Kumpulainen |
10 |
| 252 |
1980 |
C/32/80 |
Force requirements in deep drawing of cylindrical shells |
A.S. Korhonen; M. Sulonen |
10 |
| 253 |
1980 |
C/33/80 |
Theory of deep-drawing of square blanks and the numerical solution of the flange region |
B. Kaftanoglu; B. Kilkis |
10 |
| 254 |
1980 |
C/34/80 |
Characterizing of the stretch behaviour of thin steel sheets |
D. Rault; M. Entringer |
8 |
| 255 |
1980 |
C/35/80 |
Effect of loading path on the formability of sheet metals |
A. Ranta-Eskola |
10 |
| 256 |
1980 |
C/36/80 |
Development and propagation of surface strain during forming of sheet steel panels |
I. Aoki; T. Horita |
8 |
| 257 |
1980 |
C/37/80 |
Studies on the static dent resistance |
Y. Yutori; S. Nomura; I. Kokubo; H. Ishigaki |
9 |
| 258 |
1980 |
C/38/80 |
Determination of forming limit curves by means of Marciniak punch |
J. Grontostajski; A. Dolny |
9 |
| 259 |
1980 |
C/39/80 |
Testing adherence of coatings using limited dome height method |
A. Mertens; L. Renard; J.M. Sacre; Smet; Moerdijck |
6 |
| 260 |
1980 |
C/40/80 |
Piercing and hole-flanging of sheet metals: a survey |
W. Johnson; S.K. Ghosh; S.R. Reid |
22 |
| 261 |
1980 |
C/41/80 |
The properties and formability of aluminum-5% magnesium alloy clad with an austenitic stainless steel |
B.W. Murray; W.T. Roberts; D.V. Wilson |
10 |
| 262 |
1980 |
C/42/80 |
The elevated temperature behaviour of some Al-Mg alloys |
M.J. Painter; R. Pearce |
18 |
| 263 |
1980 |
C/43/80 |
Press-hardening. The influence of sheet metal and tool design on the production rate |
G. Berglund; K. Kallstrom; L. Melin |
10 |
| 264 |
1982 |
C/1/82 |
The practice of weight reduction in autobodies using HS steels |
G. Arrigoni; E. Carli |
13 |
| 265 |
1982 |
C/2/82 |
The use of HSLA steel sheets in two wheeled and three wheeled vehicles |
E. Bocalari; R. Daglio; W. Irmici; G. Montano |
12 |
| 266 |
1982 |
C/3/82 |
High strength steel sheet. Application to the automobile industry. |
G. Lefevre; R. El Haik |
17 |
| 267 |
1982 |
C/4/82 |
Material and energy can be saved by proper use of high strength steels |
J. Ribeca |
10 |
| 268 |
1982 |
C/5/82 |
Metallurgical effects on the strain hardening of aluminum sheet forming |
H.P. Falkenstein; W. Gruhl; G. Scharf |
11 |
| 269 |
1982 |
C/6/82 |
Surface roughening and strain inhomogeneities in aluminum sheet forming |
P.M.B. Rodrigues, R. Akeret |
12 |
| 270 |
1982 |
C/7/82 |
Improved formability for medium strength aluminum alloys through microstructural control |
P.W. Beaver; B.A. Parker |
12 |
| 271 |
1982 |
C/8/82 |
The stretch-formabilities of precipitation-hardening aluminum alloys at temperatures up to 500C |
G. L'Esperance; W.T. Roberts; M.H. Loretto; D.V. Wilson |
11 |
| 272 |
1982 |
C/9/82 |
High strength cold-rolled steel sheet for automotive applications **THIS TRANSCRIPT IS NOT AVAILABLE |
N.A. Cantalejos; A. Hey |
N/A |
| 273 |
1982 |
C/10/82 |
The effect of microstructure and texture upon the mechanical properties of hot rolled dual phase steels |
C.M. Vlad; U. Feldman; H.J. Bunge |
9 |
| 274 |
1982 |
C/11/82 |
The effect of strain induced martensite on the strength and formability of metastable austenitic stainless steel sheets |
R. Rintamaa; M. Sulonen |
12 |
| 275 |
1982 |
C/12/82 |
Development of formable ultra high strength cold rolled steel sheet |
M. Takahashi; N. Nagao; K. Saiko; A. Okamoto |
10 |
| 276 |
1982 |
C/13/82 |
The effect of punch surface roughness on the deep drawability of metals |
D. Spurgeon; A. Younger |
12 |
| 277 |
1982 |
C/14/82 |
Production of surface textured work rolls by means of laser pulses |
J. Crahay; A. Bragard |
12 |
| 278 |
1982 |
C/15/82 |
Comparison of strip drawing tests used for measuring surface interactions in press forming |
A. Ranta-Eskola; J. Kumpulainen; M. Sulonen |
10 |
| 279 |
1982 |
C/16/82 |
Tribology & Die Design **TRANSCRIPT NOT AVAILABLE |
G. Ziaja; G. Krallics; G. Horvath |
N/A |
| 280 |
1982 |
C/17/82 |
New ways of improving the surface properties of metal forming tools |
A. Korhonen; E. Sirvio; H. Sundquist |
8 |
| 281 |
1982 |
C/18/82 |
Frictional forces in press forming of laminated steel |
L.E. Melin; K.I. Nilsson |
6 |
| 282 |
1982 |
C/19/82 |
Relation between surface morphology characteristics and gripping |
M. Zeiger; A. Beck-Schoenenberger |
12 |
| 283 |
1982 |
C/20/82 |
Analysis of elastic recovery by means of the Yoshida buckling test |
J.M. Jalinier; H. Hayashi; O. Shibasaki; K. Yoshida |
10 |
| 284 |
1982 |
C/21/82 |
Effect of mechanical properties on the growth of wrinkles in sheet metal forming |
I. Aoki; T. Matoba; M. Ataka |
9 |
| 285 |
1982 |
C/22/82 |
Analysis of buckling and fitting behaviour in press forming of cold rolled steel sheets. |
H. Abe; T. Hira; T. Sasaki; K. Nakagawa |
11 |
| 286 |
1982 |
C/23/82 |
A study of the removal technique for surface deflection |
Y. Ueno; N. Yoshihara; H. Ishigaki; N. Nakagawa |
12 |
| 287 |
1982 |
C/24/82 |
Improvements in the dent resistance of large automotive panels |
J.L. White; G.E. Atkins |
10 |
| 288 |
1982 |
C/25/82 |
Analysis of fitting behaviour and fittability in press forming of large-sized autobody panels |
H. Ishigaki; N. Nakagawa; K. Arima |
12 |
| 289 |
1982 |
C/26/82 |
Quality evaluation method for pressformed parts made from steel sheet |
K.W. Blumel |
9 |
| 290 |
1982 |
C/27/82 |
The denting behaviour of some sheet materials |
M.J. Painter; R. Pearce |
12 |
| 291 |
1982 |
C/28/82 |
Formability problems and fatigue perfromance of HSS for wheel discs **TYPESCRIPT NOT AVAILABLE |
S. Corso; S. Gubian; M. Palladino |
N/A |
| 292 |
1982 |
C/29/82 |
Application of High Strength steel sheets for outer panels of autobodies |
P.M. Wollrab; H. Drecker |
11 |
| 293 |
1982 |
C/30/82 |
Specific energy absorption and vehicle weight - Criteria for the use of high-strength steels in energy absorbing structures |
M. Rauser; U. Bez |
10 |
| 294 |
1982 |
C/31/82 |
Improved energy absorption with high strength dual-phase steel sheets |
J.O. Sperle; H. Lundh |
10 |
| 295 |
1982 |
C/32/82 |
Cyclic & monotonic mechanical performance of sheet steels after forming **TYPESCRIPT NOT AVAILABLE |
H.R. Piehler; P.L. Charpentier |
N/A |
| 296 |
1982 |
C/33/82 |
Development of steels for automobile wheels |
P.C. Makin; B.G. Wilson; J.G. Williams; J. Szalla; R.M. Hobbs |
10 |
| 297 |
1982 |
C/34/82 |
The use of aluminum body panels by Ferrari car models |
C. Federici; A. Catanzano; M. Conserva |
14 |
| 298 |
1982 |
C/35/82 |
Structural applications for cold roll ultra high strength steels **TYPESCRIPT NOT AVAILABLE |
B.S. Levy |
N/A |
| 299 |
1982 |
C/36/82 |
Some aspects of HSCR sheets for autobodies |
U. Kalla et al |
10 |
| 300 |
1982 |
C/37/82 |
Sheet metal forming in the automobile industry. Respective roles of the deformation capacity & sliding of the sheet metal on the forming tools |
Y. Deleon; J. Daigne; G. Lefevre; R. El Haik |
11 |
| 301 |
1982 |
C/38/82 |
Forming properties of some aluminum alloys sheets for car-body use |
F. Gatto; D. Morri |
21 |
| 302 |
1982 |
C/39/82 |
Application of aluminum alloy sheet to autobody parts |
M. Miyahara; Y. Yutori; S. Nomura; I. Kokubo |
10 |
| 303 |
1984 |
C/1/84 |
Strain measurement over large areas of an industrial stamping |
E. Chu; R. Sowerby; R. Soldaat; J.L. Duncan |
14 |
| 304 |
1984 |
C/2/84 |
Case studies using grid square strain analysis |
T.J. Nihill; W.R. Thorpe |
11 |
| 305 |
1984 |
C/3/84 |
Substitution of a low carbon steel with a re-phosphorized variety for an automotive panel: the application of grid square strain analysis |
W.R. Thorpe; T.J. Nihill |
12 |
| 306 |
1984 |
C/4/84 |
Study of surface deflection in door outer panel |
T. Shimomura; M. Yoshida |
8 |
| 307 |
1984 |
C/5/84 |
A study of the growth mechanism and removal techniques of surface techniques of surface deflection observed in autobody outer panels |
T. Satoh; T. Amaike; Y. Tokunaga; H. Takizawa; S. Ujihara |
8 |
| 308 |
1984 |
C/6/84 |
New forming method for avoiding geometrical defects of outer auto-body panels |
Y. Hayashi; M. Takatini |
11 |
| 309 |
1984 |
C/7/84 |
Analysis and control of buckling behaviour due to elastic recovery in press forming |
K. Yoshida; H. Komorida; M. Usuda; H. Hayashi; H. Oikawa; T. Ohwue; T. Amaike |
12 |
| 310 |
1984 |
C/8/84 |
Theoretical description of the effect of strain path on the FLD by using the new Hill's yield criteria **TYPESCRIPT NOT AVAILABLE |
J. Gronostajski |
N/A |
| 311 |
1984 |
C/9/84 |
Effect of sheet metal thickness on forming limits |
U.S. Rao; R.C. Chaturvedi |
10 |
| 312 |
1984 |
C/10/84 |
Fluid forming of sheet metal in production |
F. Rydell; T. Johannisson; P.E. Nilsson-Jatko |
11 |
| 313 |
1984 |
C/11/84 |
Assessment of behaviour of sheet metal during hydroforming |
H.M. Shang; F.S. Chau; C.J. Tay; S.L. Toh |
12 |
| 314 |
1984 |
C/12/84 |
CAD/CAM/CAE for roll forming |
W.Y.D. Yuen |
15 |
| 315 |
1984 |
C/13/84 |
Predicting the effect of die gap on flange spring back |
N.M. Wang |
15 |
| 316 |
1984 |
C/14/84 |
Springback of complex bent parts |
M.L. Chakhari; J.M. Jalinier |
12 |
| 317 |
1984 |
C/15/84 |
The effect of buckling due to residual stresses on springback measurements |
J.C. Gerdeen |
6 |
| 318 |
1984 |
C/16/84 |
Modelling of sheet metal flow through a drawbead |
J.M. Yellup |
12 |
| 319 |
1984 |
C/17/84 |
Computer aided design and deep drawing **TYPESCRIPT NOT AVAILABLE |
J. Triouleyre |
N/A |
| 320 |
1984 |
C/18/84 |
Development of high purity ferritic stainless steel with excellent stretchability |
K. Miyakusu; Y. Uematsu; K. Hoshino |
12 |
| 321 |
1984 |
C/19/84 |
Characteristics of continuous-annealed steel sheets for automotive use |
S. Satoh; T. Obara; K. Hasiguchi; M. Nishida; T. Irie; N. Urayama |
12 |
| 322 |
1984 |
C/20/84 |
High Strength steel heet for automotive applications manufacturing properies and functional performance |
E.J. Drewes; W. Gorissen; H. Litzke; W. Muschenborn; J. Schmidt-Zinges; C. Schneider; C. Vlad |
11 |
| 323 |
1984 |
C/21/84 |
Formability of high strength hot-rolled steels for automobile suspension and reinforcement parts |
T. Takano; K. Abe; M. Usuda |
12 |
| 324 |
1984 |
C/22/84 |
Shape accuracy and denting behaviour criteria for the selection of high strength steel sheet |
W. Muschenborn, O. Maid; K. Blumel; G. Hartmann; W. Bleck |
11 |
| 325 |
1984 |
C/23/84 |
Formability and work-hardening in a strip cast AlMn(Mg) Alloy **TYPESCRIPT NOT AVAILABLE |
J. Tibbals |
N/A |
| 326 |
1984 |
C/24/84 |
Fine grained zinc alloy sheet with high strength good formability |
B.A. Parker; G.J. Geist |
8 |
| 327 |
1984 |
C/25/84 |
Control of earing in Al-Mg alloys |
B. Anderson; S.E. Naess |
10 |
| 328 |
1984 |
C/26/84 |
The deformation and fracture mechanism of dual phase steel sheets under biaxial stress combinations |
G. Pirvu |
9 |
| 329 |
1984 |
C/27/84 |
Deep Drawability of dual-phase steel |
R.K. Ray |
12 |
| 330 |
1984 |
C/28/84 |
Recrystallization textures of deep drawing steels for press forming applications **ABSTRACT ONLY |
S. Mishra |
1 |
| 331 |
1984 |
C/29/84 |
Sheet metal forming in small series production |
L. Melin |
10 |
| 332 |
1984 |
C/30/84 |
Quick change tooling techniques **ABSTRACT ONLY |
P. Kloe |
1 |
| 333 |
1984 |
C/31/84 |
Flexible panel production **ABSTRACT ONLY |
J.M. Day |
1 |
| 334 |
1984 |
C/32/84 |
Flexible fabricating in sheet metal industry **LONG ABSTRACT ONLY |
C. Law |
4 |
| 335 |
1984 |
C/33/84 |
Behaviour of galvanized coatings during forming |
S. Makimattila; A. Ranta-Eskola |
12 |
| 336 |
1984 |
C/34/84 |
A new method for evaluating the powdering phenomenon of pre-coated sheet metals |
M Shiokawa; H. Takizawa; S. Ujihara; Y. Hayashi |
12 |
| 337 |
1984 |
C/35/84 |
Analysis of formability and some problems in stamping of coated steel sheets |
M. Ejima; Y. Tokunaga; T. Honda |
12 |
| 338 |
1984 |
C/36/84 |
Formability of aluminum coated steel sheet |
T. Yamada; H. Kawase |
10 |
| 339 |
1984 |
C/37/84 |
Luders band patterns and their effect on the properties and performance of metallic coated steel strip |
F. A. Rose |
11 |
| 340 |
1984 |
C/38/84 |
The influence of strain size on the instantaneous anisotropy parameter in a low carbon steel |
P.I. Welch; H.J. Bunge |
10 |
| 341 |
1984 |
C/39/84 |
Stress-strain relationship in simple shear of in-plane deformation for various steel sheets |
K. Miyauchi |
12 |
| 342 |
1984 |
C/40/84 |
Parameters affecting the strain rate sensitivity of aluminum alloys |
R.G. O'Donnell; B.A. Parker |
11 |
| 343 |
1984 |
C/41/84 |
Thermal gradients, strain rate, and ductility in sheet steel tensile specimens |
R.A. Ayres |
11 |
| 344 |
1984 |
C/42/84 |
The study of the dynamic dent resistance |
S. Nomura; Y. Yutori; J. Iwaya; M. Miyahara; I. Kokubo |
9 |
| 345 |
1984 |
C/43/84 |
Optimizing patterns and computational algorithms for automated, optical strain measurement in sheet metal |
D.N. Harvey |
12 |
| 346 |
1984 |
C/44/84 |
A shear test for sheet metal bendability |
S.N. Rasmussen |
12 |
| 347 |
1984 |
C/45/84 |
The differential work hardening coefficient and classical work hardening laws |
L. Ratke; P.I. Welch |
9 |
| 348 |
1984 |
C/46/84 |
On the definition of acceptable anisotropy parameters for formability testing |
P.I. Welch; L. Ratke; H.J. Bunge |
8 |
| 349 |
1984 |
C/47/84 |
Anisotropic behaviour of sheet metals in proportional and non-proportional straining |
A. Barata da Rocha; F. Barlat; J.M. Jalinier |
13 |
| 350 |
1984 |
C/48/84 |
Analysis of surface defects and side wall curl in press forming **KEYNOTE PAPER |
Y. Hayashi |
16 |
| 351 |
1984 |
C/49/84 |
A user's view of computer modelling techniques for die design **KEYNOTE PAPER - TYPESCRIPT NOT AVAILABLE |
W. Brazier |
N/A |
| 352 |
1984 |
C/50/84 |
Developments in sheet materials for forming applications **KEYNOTE PAPER |
R.M. Hobbs |
11 |
| 353 |
1984 |
C/51/84 |
Flexible manufacturing for the sheet metal industry **KEYNOTE PAPER - TYPESCRIPT NOT AVAILABLE |
J. Wallace |
N/A |
| 354 |
1984 |
C/52/84 |
On the possibility of a unique test for sheet metal formability **KEYNOTE PAPER |
B. Levy |
14 |
| 355 |
1986 |
C/1/86 |
Modern methods for Car Body Design |
Pr. Dr. Techn. E. Fiala; Dr. -ing. U. Sorgatz |
30 |
| 356 |
1986 |
C/2/86 |
Development of Press-forming processes for Autobody Panels |
Dipl. Ing. W. Jacobi |
31 |
| 357 |
1986 |
C/3/86 |
Chemical Surface Treatment and Corrosion Protection in the Automotive Industry |
W. Dr. Rer. Nat. Menzer |
25 |
| 358 |
1986 |
C/4/86 |
Concept of a New Continuous Annealing Line for Steel Sheet |
E.J. Drewes; B. Engl; K.L. Trultzsch |
11 |
| 359 |
1986 |
C/5/86 |
Structural Parameters of Dual-Phase Steels Determining the Stress/Strain Curve |
O. Maid |
11 |
| 360 |
1986 |
C/6/86 |
The Bake-Hardening Potential of Box-Annealed cold-rolled Sheet Steel |
H. Litzke; R. Muller |
10 |
| 361 |
1986 |
C/7/86 |
Application of High-Strength Steel Sheets in Autobody Pressing - Chances and Limitations |
P.M. Wollrab; M. Streidl |
10 |
| 362 |
1986 |
C/8/86 |
Formability of Steel-Plastic-Steel Laminate |
M. Shinozaki; Y. Matsumoto; K. Tsunoyama; T. Irie |
9 |
| 363 |
1986 |
C/9/86 |
Mechanical Properties and formability of Fine Grained Aluminum Alloy Sheet |
R. Mahmudi; W.T. Roberts; D.V. Wilson |
10 |
| 364 |
1986 |
C/10/86 |
Variation of Automobile Panel Properties Due to the Manufacturing Process |
K. Blumel; G. Hartmann; P. Lubeck |
9 |
| 365 |
1986 |
C/11/86 |
The influence of Tool Pressure on Thickness Strain over the Flat Bottom of Stretch-Formed Shells |
Z. Marciniak; J. Kolodziejski |
10 |
| 366 |
1986 |
C/12/86 |
Ironing Dynamometer for studying Wall Ironing in the Cupping Press |
X.J. Wang; L. Duncan |
17 |
| 367 |
1986 |
C/13/86 |
High Pressure Flexible Die Forming of Sheet Metal for the Automotive Industry |
T.G. Johannisson |
11 |
| 368 |
1986 |
C/14/86 |
Surface Quality Requirements for Sheet Metal in Car Bodies |
R. Harlfinger; A. Jurgetz; M. Streidl |
8 |
| 369 |
1986 |
C/15/86 |
Methods of evaluating the Fabricability of Precoated Sheet Metal and Repercussions on the Quality of Car Components |
B. Hochon; Y. Deleon; A. Jussiaume; D. Perry |
11 |
| 370 |
1986 |
C/16/86 |
Influence of the Deformation on the Corrosion Resistance of Painted Coated Steel Sheets |
G. Monfort; A. Bragard |
10 |
| 371 |
1986 |
C/17/86 |
Effect of Surface Chemical Condition on the Frictional Properties of Hot-Dip Galvanized Steel Sheets |
S. Makimattila; E. Ristolainen |
10 |
| 372 |
1986 |
C/18/86 |
A Three Dimensional Forming Limit/Stress State Concept for Evaluating Coating Damage in Sheet Metal Forming |
B.S. Levy |
13 |
| 373 |
1986 |
C/19/86 |
Evaluation of a New Surface-Treated Steel Sheet Called "Dura-Steel" and its Applications to Auto Bodies |
T. Furubayashi; A. Sato; H. Hirano |
10 |
| 374 |
1986 |
C/20/86 |
New Technological Research on Testing Methods and Cold-Bending of Coated Steel Sheets |
A. Neubauer; H.J. Rasehorn |
10 |
| 375 |
1986 |
C/21/86 |
Influence of Sheet Surface Roughness on the Top-Coat Appearance in Autobodies Painting Processes |
G. Arrigoni; M. Sarracino |
9 |
| 376 |
1986 |
C/22/86 |
The LDH Test - Experiments and Computer Simulation |
J.C. Gerdeen; W.G. Brazier |
14 |
| 377 |
1986 |
C/23/86 |
The Importance of Materials Data in the Simulation of Sheet Forming Process |
J. Reissner; W. Schmid |
12 |
| 378 |
1986 |
C/24/86 |
The Simulation of the Sheet Metal Forming Process Using Numerical Models of Increasing Complexity |
J. Berland; J.M. Detraux; F. Horkay; J.M. Jalinier; C. Manh |
12 |
| 379 |
1986 |
C/25/86 |
The Coaxial and Non-Coaxial Strain Paths in Finite Deformation |
E. Chu |
10 |
| 380 |
1986 |
C/26/86 |
The Simulation of Forming Severity on Autobody Panels Using a CAD System - Behaviour of Materials after Passing Drawbead |
T. Furubayashi; H. Misaka; S. Ujihara; T. Sakamoto |
20 |
| 381 |
1986 |
C/27/86 |
Computer-Aided Evaluation Method for Sheet Metal Forming in Car Body |
H. Yamasaki; T. Nishiyama; K. Tamura |
10 |
| 382 |
1986 |
C/28/86 |
Development of Textures in a Dual-Phase Steel With Reference to Its Deep-Drawability |
R.K. Ray |
10 |
| 383 |
1988 |
C/1/88 |
A Systems Approach to Sheet Metal Forming Process Control |
J. F. Siekirk |
8 |
| 384 |
1988 |
C/2/88 |
Variations of the Stamping Process |
K.W. Blumel; G. Hartmann; P. Lubeck |
8 |
| 385 |
1988 |
C/3/88 |
Thermograph - An Aid to Press Shop Process Control |
T.J. Nihill; J.L. White |
8 |
| 386 |
1988 |
C/4/88 |
Stamping Automotive Body Panels with Pre-Lubricated Steel |
A. Vadhavkar |
5 |
| 387 |
1988 |
C/5/88 |
The Influence of the Interaction Between the Coating and the Sheet Steel Base on the Formability of Al-Zn Coated Steel |
D.J. Willis; J.S.H. Lake |
11 |
| 388 |
1988 |
C/6/88 |
Study of Damage Sustained by Precoated Sheet Steel During Deformation and Effect on Corrosion Resistance **TRANSCRIPT NOT AVAILABLE |
D. Perry; A. Jussiaume; Y. Deleon |
N/A |
| 389 |
1988 |
C/7/88 |
Analysis of Formability of Coated Steel Sheet at Complex Strain Paths |
J.Z. Gronostajski; W.J. Ali |
5 |
| 390 |
1988 |
C/8/88 |
Influence of Forming of Coated Steel Sheets on the FLD and Corrosion Resistance |
J. Z. Gronostajski; M.S. Ghattas |
6 |
| 391 |
1988 |
C/9/88 |
Characterization of Friction Properties During Sheet Forming |
E. Schedin; K. Fredriksson; C. Gustafsson |
7 |
| 392 |
1988 |
C/10/88 |
Strip Drawing of Boundary Lubricated Uncoated and Precoated Steel Sheets: Frictional Response and Metal Transfer as a Function of Tool Surface |
J. Von Stebut; D. Perry |
8 |
| 393 |
1988 |
C/11/88 |
The Influence of Surface Roughness on Friction |
W.C. Emmens |
8 |
| 394 |
1988 |
C/12/88 |
Tribological Approach - Reliable Method for Estimating the Effects of Contact Friction in Deep Drawing |
M. Stefanovic |
5 |
| 395 |
1988 |
C/13/88 |
Frictional Characteristics of Coated Steel Sheets |
S. Nakamura; M. Yoshida; A. Nishimoto |
7 |
| 396 |
1988 |
C/14/88 |
Strip Friction Experimental Study on Galvanized Steel Sheet |
R. Zheng; D. Overby |
6 |
| 397 |
1988 |
C/15/88 |
Progress in the Roughness Texture of the Cold Rolled Steel Sheets Related to Deep Drawing and Forming |
G. Monfort; J. De Fourny; A. Bragard |
8 |
| 398 |
1988 |
C/16/88 |
Evaluation of the Properties of Sheet with Lasertex Surface Texture |
R. Muller |
9 |
| 399 |
1988 |
C/17/88 |
Development of High Image Clarity Steel Sheet by the Application of Laser Texturing |
M. Imanaka; T. Fujiwara; T. Furubayashi; T. Obara; K. Tunoyama; K. Furukawa |
8 |
| 400 |
1988 |
C/18/88 |
Influence of Surface Morphology on the Appearance of Cold Rolled Steel Sheet After Painting |
V. Cascioli; A. Segala; P.L. Antoniucci |
8 |
| 401 |
1988 |
C/19/88 |
Surface Structure Changes of Containing Phosphorous Steel Sheet during Uniaxial Tension |
X. Cheng; Q. Yao; Y. Zhang |
7 |
| 402 |
1988 |
C/20/88 |
The Influence of Constitutive Behaviour on Predicted Sheet Metal Forming Limits |
D.D. Olander; A.K. Miller |
12 |
| 403 |
1988 |
C/21/88 |
On the Effect of Strain Path on the Forming Limit of Sheet Metal |
B. Devedzic |
9 |
| 404 |
1988 |
C/22/88 |
Estimation of Flow Stress in Secondary Deformation of Prestrained Sheet Steels |
M. Usuda. Y. Ishii |
7 |
| 405 |
1988 |
C/23/88 |
Limitations Non-Quadratic AnisotropicYield Criteria and Their Use in Analyses of Sheet Forming |
W.F. Hosford |
8 |
| 406 |
1988 |
C/24/88 |
Certain Aspects of the Limiting Drawing Ratio in Sheet Metal Forming Processes |
E. Chu; M.F. Shi; J.C. Gerdeen |
13 |
| 407 |
1988 |
C/25/88 |
Sheet Metal Forming Modeling of Automotive Body Panels |
S.C. Tang; J. Gress; P. Ling |
9 |
| 408 |
1988 |
C/26/88 |
Finite Element Simulation of Bending Process of Steel-Polymer-Steel Laminate Sheet |
A. Makinouchi; H. Ogawa; K. Hashimoto |
10 |
| 409 |
1988 |
C/27/88 |
Model of Drawbead Forces in Sheet Metal Forming |
T.B. Stoughton |
11 |
| 410 |
1988 |
C/28/88 |
A General Computer Model for Plane Strain Sheet Flow and Its Application to Flow Between Circular |
L.R. Sanchez; K.J. Weinmann |
10 |
| 411 |
1988 |
C/29/88 |
The Analysis of Side-Wall Curl Control |
C. Chu |
4 |
| 412 |
1988 |
C/30/88 |
The Axi-Symmetric Stretch Flanging of Sheet Steel |
M.Y. Demeri |
6 |
| 413 |
1988 |
C/31/88 |
Prediction of Flangeability of Circular Holes in A Metal Sheet |
W. Zhou |
5 |
| 414 |
1988 |
C/32/88 |
Recent Developments in CAD/CAM Techniques Used to Design Automotive Deep Drawing Parts **MANUSCRIPT NOT AVAILABLE |
R. De Oliviera; J.M. Detraux; F. Horkay |
N/A |
| 415 |
1988 |
C/33/88 |
Simulation of Forming Severity on Autobody Panels Using a CAD System-Analysis of Drawbead and Its Control |
T. Furubayashi; S. Ujihara; T. Sakamoto |
8 |
| 416 |
1988 |
C/34/88 |
Computer Aided Evaluation of Forming Severity for Automotive Stampings |
M.P. Sklad |
14 |
| 417 |
1988 |
C/35/88 |
Computer Aided Sequence Design for Forming of Axisymmetrical Shapes |
J. Kolodziejski |
N/A |
| 418 |
1988 |
C/36/88 |
Method for Sheet Material Forming |
J.H. Vogel; J. Amoedo; D. Lee |
7 |
| 419 |
1988 |
C/37/88 |
The Development of "Die Face CAD" |
S. Nishimura; H. Sugiura; S. Nakamura |
N/A |
| 420 |
1988 |
C/38/88 |
The Limiting Dome Height Punch Test: An Analysis of Sensitivity and Variability |
D.A. Burford; D.K. Matlock; G. Krauss |
9 |
| 421 |
1988 |
C/39/88 |
Formability of Steel-Plastic Laminated Sheets |
K. Hashimoto; T. Ohwue; M. Takita |
9 |
| 422 |
1988 |
C/40/88 |
Press Formability of Steel-Resin-Steel Laminates for Vibration Damping |
M. Kojima |
7 |
| 423 |
1988 |
C/41/88 |
Improvement of the Aging Properties of Hot-Dip Zinc-Coated Sheet Steels by Continuous Overaging |
S. Makimattila; M. Roukanen; S. Lankila |
8 |
| 424 |
1988 |
C/42/88 |
Residual Stresses After Axisymmetric Deep Drawing |
C. Teodosiu; H. Cao |
11 |
| 425 |
1988 |
C/43/88 |
Using Para-Ellipse as the Shape of the Sheet Metal Blanks for Deep Drawing Box |
H. Cao |
7 |
| 426 |
1990 |
C/1/90 |
Mechanical Characteristics of Both-sided Ironing Prcess and Ironed Cans |
T. Aoki; K. Miyauchi |
8 |
| 427 |
1990 |
C/2/90 |
Influence of Forming Condition and Panel Surface Stiffness on Shape Fixability and Surface Distortion |
K. Kunitake; A. Kodama; M. Kudo; T. Nagamitsu; K. Hashimoto; M. Takita |
8 |
| 428 |
1990 |
C/3/90 |
Real-Time Control of Binder Force During Stamping |
D.E. Hardt; M.C. Boyce; R.P. Fenn |
12 |
| 429 |
1990 |
C/4/90 |
Formability of Stainless Steels |
R. Johansson; H. Groth; E. Schedin |
14 |
| 430 |
1990 |
C/5/90 |
Effect of the Surface Quality of the Workpiece Material on the Frictional Behaviour During Sheet Forming |
B.T. Meier; J. Reissner; M. Bloeck |
10 |
| 431 |
1990 |
C/6/90 |
The Test of Simple Shear: Experimental Techniques and Application to the Identification of Constitutive Laws for Metal Sheet |
P. Genevois; F. Moussy; C. Teodosiu |
10 |
| 432 |
1990 |
C/7/90 |
Nonproporational Deformation Paths in Progressive Die Forming |
M.P. Sklad; C.B. Harris; B.A. Yungblud |
8 |
| 433 |
1990 |
C/8/90 |
Process Signatures - Product and Process Perspectives |
M. Karima; W. Tse |
10 |
| 434 |
1990 |
C/9/90 |
On Formability of Sheet Aluminum |
N. Asnafi; C. Magnusson |
12 |
| 435 |
1990 |
C/10/90 |
Residual Stress Phenomena Due to Cold-Bending of Steel |
L. Ingvarsson |
10 |
| 436 |
1990 |
C/11/90 |
Friction Effects on Formability of Sheet Metals |
J.C. Gerdeen; B.A. El-Jaam |
10 |
| 437 |
1990 |
C/12/90 |
Die Friction Variations in Simulated Sheet Metal Forming |
R.N. Wright; T. Schurman |
10 |
| 438 |
1990 |
C/13/90 |
Friction Mechanisms During Sheet Forming |
E. Schedin; A. Thuvander |
8 |
| 439 |
1990 |
C/14/90 |
The Influence of Aging on the Properties of Hot-Dip Zn Coatings |
G. Engberg; A. Haglund; S.E. Hornstrom |
12 |
| 440 |
1990 |
C/15/90 |
Formability and Solderability of Tin and Tin/Lead Coatings on brass Strips |
A. Kamf; R. Sundberg; S. Karlsson; A. Thuvander |
10 |
| 441 |
1990 |
C/16/90 |
Effect of Temperature, Die Materials and Lubricant on Sliding Behaviour of Various Coated Steel Sheets |
K. Hashimoto; T. Ohwue; M. Takita |
8 |
| 442 |
1990 |
C/17/90 |
The Influence of Contact Temperature on Metal Transfer and Galling in Strip Drawing |
X Roizard; J. Von Stebut; B. Paintendre; L. Venumiere |
12 |
| 443 |
1990 |
C/18/90 |
Press Formability of Various coated Steel Sheets |
T. Hishida; T. hisatsune; M. Yoshida |
10 |
| 444 |
1990 |
C/19/90 |
Evaluation of forming Parameters in Galvanized sheet Steel forming Processes |
H.C. Liu; D. Lee |
8 |
| 445 |
1990 |
C/20/90 |
A Study on the Frictional Behaviour of Coated Steel Sheets |
J. Iwaya; Y. Okano; M. Miyahara |
8 |
| 446 |
1990 |
C/21/90 |
Tribological Factors in the Stamping of Coated and Uncoated Steel Sheets |
G. Monfort; J. Defournay |
10 |
| 447 |
1990 |
C/22/90 |
Effect of Coating Layer and Lubricant oil on the Formability of Coated Steel Sheet |
T. Morishita; T. Horita |
8 |
| 448 |
1990 |
C/23/90 |
Research on Forming Characteristics of Laminated Damping Sheets for Deep Drawing |
X. Cheng; L. Zhang |
8 |
| 449 |
1990 |
C/24/90 |
In Service Resistance to Cosmetic Corrosion of Coated Steel Sheets |
B. Schmitz; J.P. Serviais; G. Monfort; J. Defourny; V. Leroy |
10 |
| 450 |
1990 |
C/25/90 |
The Effect of Zinc Coating Thickness on the Formability and Corrosion Resistance of Sheet Steel |
J.Z. Gronostajski |
6 |
| 451 |
1990 |
C/26/90 |
Flexforming for Short Series Sheet Metal Forming |
T.G. Johannisson |
8 |
| 452 |
1990 |
C/27/90 |
Superplastic Forming of Sheet Metal |
C. Magnusson; U. Ohman |
8 |
| 453 |
1990 |
C/28/90 |
Theoretical and Experimental Investigation of Super-Plastic Sheet Metal Forming |
M. Tisza |
8 |
| 454 |
1990 |
C/29/90 |
Practical Consequences of Limitations in constitutive Equations in Predicting Sheet Metal Forming |
B.S. Levy |
12 |
| 455 |
1990 |
C/30/90 |
Design of Forming Stages with Elementary Calculation Methods |
E. Doege; H. Simon; F. Boinski |
10 |
| 456 |
1990 |
C/31/90 |
Simple Mathematical Models for Predicting Can Wall Thickening and Can Wall Elongation in Die Necking Processes |
E. Chu |
10 |
| 457 |
1990 |
C/32/90 |
Aspects of Process Variables in Sheet Forming Simulation |
M.P. Sklad; J.F. Siekirk |
10 |
| 458 |
1990 |
C/33/90 |
Press Formability of Laser Welded Blanks |
K. Azuma; K. Ikemoto; K. Arima; H. Sugiura; T. Takasago |
8 |
| 459 |
1990 |
C/34/90 |
3D FEM Analysis of Sheet Metal Forming Problem |
A. Cella; G.L. Raffeto; M. Guida; A. Messina; P.P. Strona; F. Panico |
10 |
| 460 |
1990 |
C/35/90 |
Some Aspects Relating to the Modeling of Stamping Operations with Finite Elements |
J. Defourny; G. Monfort; M. Traversin; E. Abreu; R. D'Haeyer; V. Leroy |
8 |
| 461 |
1990 |
C/36/90 |
Nucleation and Propagation of Defects During Forming of Coated Steel Sheets |
J.Z. Gronostajski |
8 |
| 462 |
1990 |
C/37/90 |
Estimation of limiting drawing Ratio in cup Drawing |
G. Jun; J.W. Lee |
8 |
| 463 |
1990 |
C/38/90 |
Effect of Zn-Ni Plating on Mechanical Properties and Press Formability of Sheet Steels |
T. Kato; M. Imanaka; C. Kato; A. Yasuda; H. Abe; K. Tunoyama |
8 |
| 464 |
1990 |
C/39/90 |
Production Experience and Properties of Hot-Dip Galvanized Dual-Phase Steels |
A.S. Lankila |
8 |
| 465 |
1990 |
C/40/90 |
Mathematical Modeling of V-Die Bending Process |
C. Magnusson; Z. Tan |
8 |
| 466 |
1990 |
C/41/90 |
Problems of FEM Analysis in Sheet Metal Forming Under Strain Gradient |
K. Miyauchi |
8 |
| 467 |
1990 |
C/42/90 |
Study on Method of Evaluation for Frictional Characteristics in Coated Steel Sheets |
S. Nakamura; M. Yoshida; A. Nishimoto; T. Ono |
8 |
| 468 |
1990 |
C/43/90 |
A Formability Study of a Drawing Galvanized Steel Sheet |
Cai Jian Nan |
10 |
| 469 |
1990 |
C/44/90 |
Super Formative Steel Sheet with Excellent Stretchability and Low Effective Yield Strength |
C. Sudo; Y. Hirose; Y. Hayashi |
8 |
| 470 |
1990 |
C/45/90 |
Normal Plastic Anisotropy in Galvanized and Uncoated Drawing Quality Sheet Steel |
R. Zheng; J.L. Duncan; D. Overby; R. Sowerby |
8 |
| 471 |
1990 |
C/46/90 |
Development and Validation of a General Industrial Stamping Simulation Code based on Mindlin Shell Formulation |
E. Di Pasquale; F. El-Khaldi; E. Haug; S. Aita |
8 |
| 472 |
1990 |
C/47/90 |
Blanking Tool Manufactured by Laminating Laser Cut Steel Sheets |
M.P. Schreiber; S. clyens |
8 |
| 473 |
1992 |
C/1/92 |
The Effect of Coating Microstructure on the Powdering Behaviour of Glavanneal Coated Sheet |
Zheng Ru; R. Sowerby |
7 |
| 474 |
1992 |
C/2/92 |
The Effect of Tool Material on the Galling Behaviour in the Press Forming of Coated and Uncoated Steel Sheets |
P. Belliard; B. Thomas; G. Monfort; J. Defourny |
8 |
| 475 |
1992 |
C/3/92 |
Formability of Coated Steel Sheets Evaluated by Actual Stamping Test and Laboratory Simulation Tests |
Y. Shimada; H. Ike; S. Nakamura |
8 |
| 476 |
1992 |
C/4/92 |
Interfaces and Deep Drawability of Hot-dip Galvanized Steel Sheets for Audi 100 Car |
C. Xian; L. Jiesong; G. Dehui; H. Ping; T. Shankum; Z. Lei |
8 |
| 477 |
1992 |
C/5/92 |
Frictional Behaviour in Sheet Forming of Coated Steels |
H. Abe; T. Hira; I. Yarita |
8 |
| 478 |
1992 |
C/6/92 |
Study on Frictional Characteristics of Zinc Electrodeposited Steel Sheets |
T. Ono; M. Yoshido |
8 |
| 479 |
1992 |
C/7/92 |
Lubricity Improvement of Galvannealed Steel Sheet by Surface Modification and Application of Lubricant Oil |
S. Nakamura; Y. Itoh; T. Morishita; Y. Yamanaka |
8 |
| 480 |
1992 |
C/8/92 |
Origin and Control of Looper Lines in Deep Drawn Cups |
W.B. Lee; K.Y. Yu; B. Ralph |
8 |
| 481 |
1992 |
C/9/92 |
New Method for Manufacturing Extra Deep Drawing Steel with Very High r-value |
C. Deli; W. Xianjin |
8 |
| 482 |
1992 |
C/10/92 |
Properties of Damping Steel Sheet and Its Applications |
A. Yuguo; Q. Wenyun; J. Weizhi; L. Xiya; C. Xian |
8 |
| 483 |
1992 |
C/11/92 |
Action of Phosphorus on the Annealing Texture of Low-Carbon Fe-P Alloys |
Z. Lixin; L. Liguang |
8 |
| 484 |
1992 |
C/12/92 |
The Effect of Coat on the r-Value of Galvanized Sheets |
T. Di; Q. Jiangquing; Y. Jian; W. Xiamjin |
7 |
| 485 |
1992 |
C/13/92 |
The Influence of Surface conditions of Hot-Dip Galvannealed Steel Sheet on the Drawing Force During Deep Drawing |
J. Iwaya; M. Miyahara |
8 |
| 486 |
1992 |
C/14/92 |
Effect of Tool Shape and Friction on the Galvanized Sheet Forming |
Y.L. Kang; X.J. Wang; J. Kihara; T. Aizawa; M. Usuda |
7 |
| 487 |
1992 |
C/15/92 |
Recrystallization Annealing Processing of Interstitial Free Steel |
K. Bingyu; L. Jiangxin; S. Quanshe; M. Xiachuan |
7 |
| 488 |
1992 |
C/16/92 |
Deformation Mechanism During Controlled rolling of rephosphorized Deep Drawing High Strength Sheet Steel |
M. Xuguang; Z. Jinfu; L. Guixi; D. Yingmin; W. Wenjing; S. Jianqing |
10 |
| 489 |
1992 |
C/17/92 |
Effect of Cryogenic Temperature on Mechanical Property and Luders Strain of Phosphorized Deep drawing High Strength Steel Sheet |
Y. Wanquan; G. Wei; M. Xuguang |
8 |
| 490 |
1992 |
C/18/92 |
On the Relationship of Annealing Textures in High Strength Deep Drawing Sheet Steel O8A1P vs. Dispersed Precipitated Phases and Reduction Degree of Cold Rolling |
F. Zuobao; Z. Kui; Q. Li; Z. Weihan |
8 |
| 491 |
1992 |
C/19/92 |
Effects of Retained Austenite Y(R) on Mechanical Properties, Microstructure and Formability of a Hot Rolled Low Alloy Trip Sheet Steel |
Z. Jinfu; M. Xugang; O. Lijin; D. Yingmin; C. Yuqin |
6 |
| 492 |
1992 |
C/20/92 |
Material Characterization for the CAE Finite Element Simulation of Sheet Metal Forming |
L/ Penazzi; E.D. Pasquale; S. Aita; E. Haug; C. Levaillant; D. Priadi |
17 |
| 493 |
1992 |
C/21/92 |
Material Database for Sheet Metal Forming and its simulation |
H. Hayashi |
7 |
| 494 |
1992 |
C/22/92 |
Forecasting of the Material Response in Steel Sheet Forming with implicit FEM Codes: Possibilities and Limitations |
G. Monfort; J.P. Ariaens; D. Defourny |
9 |
| 495 |
1992 |
C/23/92 |
Computer-Generated Profiles for Sheet Metal Tooling |
Z.T. Zhang; S.M. Panton; J.L. Duncan |
8 |
| 496 |
1992 |
C/24/92 |
Calculation of binder Wrap Surface Shape with Punch-Blank Contact |
K.K. Chen |
8 |
| 497 |
1992 |
C/25/92 |
Conception of Classification for Sheet Metal Drawn Parts |
X. Lu; P. Funke |
7 |
| 498 |
1992 |
C/26/92 |
Computer Aided Analysis of the Reverse Redrawing Process |
J. Chr. Folkmar Anderson |
8 |
| 499 |
1992 |
C/27/92 |
Industrial Validation of CAE Finite Element Simulation of a Stretch-Drawn Autobody Part (Front Fender Case) |
F. El Khaldi; S. Aita; L. Penazzi; T. Tamada; T. Ogawa; S. Tasaka; O. Horie |
22 |
| 500 |
1992 |
C/28/92 |
Development of Process Simulation System for Auto-Body Panel Forming by Using FE Analysis and Laser Stereolithography Techniques |
E. Nakamachi; A. Makinouchi; T. Nakagawa |
8 |
| 501 |
1992 |
C/29/92 |
Modelling of 3-Dimensional Sheet Metal Forming Processes by Membrane Model |
D. Xianghuai; L. shangjian; X. Jingrong |
5 |
| 502 |
1992 |
C/30/92 |
A Computer Aided Analysis System for Determining the Strain Path Influence on the Forming Limits of Sheet Metal Parts |
K. Albrektsen |
8 |
| 503 |
1992 |
C/31/92 |
A Methodology for Elaboration of a Microcomputer Based System in Sheet Metal Forming Process Modelling |
L. Xueshan; W. Xianjin; F. Paul |
6 |
| 504 |
1992 |
C/32/92 |
An Innovative Methodology for CAE Analysis of Sheet Metal Forming |
S. Aita; E. Eipasquale; E. Haug |
22 |
| 505 |
1992 |
C/33/92 |
A Non-QuadraSperplastic Orthotropic Yield Function Suitable for Analysis of Sheet Forming |
Z. Weixian |
8 |
| 506 |
1992 |
C/34/92 |
Plane-Strain Analysis of the Stamping Process of Auto-body Panel |
G. Jun; D.J. Yoo; J.W. Lee; H.S. Lee; C.H. Kim |
8 |
| 507 |
1992 |
C/35/92 |
Development of Forming Technique with Real-Time Control of Blank Holding Force |
Y. Hirose; M. Kojima; S. Ujihara; Y. Hishida |
8 |
| 508 |
1992 |
C/36/92 |
Cooled - Punch Deep Drawing and its Application to Automobile Parts |
T. Ohwue; M. Usuda; S. Sudo |
8 |
| 509 |
1992 |
C/37/92 |
Geometric and Material Effects in the Roll Forming of Channel Sections |
S.D. Zhu; S.M. Panton; J.L. Duncan |
8 |
| 510 |
1992 |
C/38/92 |
Forming Limits and Die Parameters of Interverting-Forming of Thin-Wall Tubes |
Y. He; L. Zhaorong |
8 |
| 511 |
1992 |
C/39/92 |
The Forming of Superplastic Metal and the Evaluation of Components Formed by Air Bulge |
W. Chunrong; S. Hailong |
5 |
| 512 |
1992 |
C/40/92 |
The Compound law on Hardening Curve of Laminated Metal Sheet |
Z. Jun; L. Shouben |
7 |
| 513 |
1992 |
C/41/92 |
Measuring Square Grids in Sheet Metal strain Analysis by Image Processing Technique |
Z. Tan; L. Melin; C. Magnusson |
8 |
| 514 |
1992 |
C/42/92 |
Implementation of computer based Image System for Grid measurement |
M.J.M. Barata marques; R.M.S.O. Baptista; S.D. Antunes |
8 |
| 515 |
1992 |
C/43/92 |
Further Analysis of Experimental Methods Used to Determine Frictional Behaviour in Sheet Metals |
D.P. Kotchman; Q.Q. Nie; H.Y. Jiang; D. Lee |
8 |
| 516 |
1992 |
C/44/92 |
New Evaluation Method for Frictional Characteristics of Zinc Coated Steel Sheets |
Y.S. Kim; W.J. Choi |
8 |
| 517 |
1992 |
C/45/92 |
A New Simulative Test to Assess Frictional Effects in Sheet Stretching |
X.J. Wang; W. Wang; F. Saunders; R.H. Wagoner |
8 |
| 518 |
1992 |
C/46/92 |
Analyzing the Deformation in the Flange of Deep Drawn Cylindrical Cups Using Different Numerical Methods |
X. Chen; R. Sowerby |
8 |
| 519 |
1992 |
C/47/92 |
A New Concept of Forming Limit Curve |
C. Guangnan; H. Shiguang |
9 |
| 520 |
1992 |
C/48/92 |
Analysis of Elastoplastic Buckling of an Anisotropic Sheet Under Non-Uniform Stretching |
X. Zhou; F. Miaohai |
8 |
| 521 |
1992 |
C/49/92 |
Buckling of Steel Sheet Subjected to Diagonal Tension (YBT) |
Y. Guang; H. Ping; L. Yuwen; L. Linsheng; Z. Tingliang |
8 |
| 522 |
1992 |
C/50/92 |
Simplified Techniques for Determining Formability of Metal Sheets |
P. Ke; W. Mongjun; G. Zhirong |
5 |
| 523 |
1992 |
C/51/92 |
Orientation Dependence of Plastic Strain Ratio in Formability Prediction |
W.B. Lee : K.C. Chan |
8 |
| 524 |
1992 |
C/52/92 |
Analysis of Sheet Wrinkling by Shear Stress and the Influence of Material Parameters on Wrinkling |
Y. Yuying; G. Gang; H. Guijin; C. Lingjiang |
8 |
| 525 |
1992 |
C/53/92 |
Experiemental Study of Tensile Instability of Metal Sheets on the left of FLD |
S. Huan; C. Guangnan; H. Shiguang |
7 |
| 526 |
1992 |
C/54/92 |
Prefer LBH to IE |
C. Zhiguo; Y. Erjun; W. Wenda; C. Xian |
4 |
| 527 |
1992 |
C/55/92 |
Highspeed Piercing of Holes in the Thin Blanks |
Y. Shamarin |
4 |
| 528 |
1992 |
C/56/92 |
Sheet Steel and Its Forming Technique in China Today and Tomorrow |
S. Changxy; C. Xian |
11 |
| 529 |
1992 |
C/57/92 |
Forming Choices |
R. Pearce |
6 |
| 530 |
1992 |
C/58/92 |
State of Arts in Japanese Auto Body Stamping and its Tooling |
T. Nakagawa |
N/A |
| 531 |
1992 |
C/59/92 |
Trends in Sheet Metal Forming in China |
X.J. Wang; J.L. Duncan |
6 |
| 532 |
1992 |
C/60/92 |
Recent Development and Formability Research of Automotive Sheet Steel |
T. Kikuma; M. Usuda |
10 |
| 533 |
1994 |
C/1/94 |
Recent Developments in Portuguese Sheet metal Forming Technology: Industrial Characterization and Research Resources |
V. Sanches e Sa; A. Barata da Rocha; M.J.M. Barata Marques |
21 |
| 534 |
1994 |
C/2/94 |
Formability and Panel Quality of Extra Deep Drawing Quality High Strength Steel Sheets |
J. Fukumoto; T. Ono; M. Yoshida |
8 |
| 535 |
1994 |
C/3/94 |
Formability and Component Tests for Higher Strength Automotive Steel Sheets |
K.M. Radlmayr; H. Ponschab; M. Blaimschein |
16 |
| 536 |
1994 |
C/4/94 |
Formability of Steel/Aluminum Clad Sheet |
Y. Hirose; A. Yahiro; S. Sudoh |
8 |
| 537 |
1994 |
C/5/94 |
The Influence of Texture on the Deformation Behaviour of Electrodeposited Ainc Coatings |
A. DeBoeck; M. VanThournout; J.M. Van Der Hoeven |
12 |
| 538 |
1994 |
C/6/94 |
Directional Effects in Bake Hardened Steels |
W.T. Roberts; D.V. Wilson |
12 |
| 539 |
1994 |
C/7/94 |
The Interrelation of Strain Hardening Anisotropy Parameter X Value and Sheet Metal Formability |
D. Zhi; W. Xianjin |
6 |
| 540 |
1994 |
C/8/94 |
Galvannealed Steel with Superior Pres Formability and Image Clarity |
M. Miura; T. Hira; T. Kato |
5 |
| 541 |
1994 |
C/9/94 |
The Influence of Thin Organic Coatings on the forming Properties of Steel Sheets for Automotive Use |
F. Androsch; K. Koster; K.M. Radlymayr |
17 |
| 542 |
1994 |
C/10/94 |
Evaluation of Specific Characteristics of Zinc Coated Deep Drawing Sheets |
F. Simak; J. Billy; B. Stefan; A. Holly |
12 |
| 543 |
1994 |
C/11/94 |
Dimensional Inaccuracy of Aluminum Alloy Sheets in Hat-Shape Forming |
H. Hayashi; A. Makinouchi; K. Murayama; T. Nakagawa |
9 |
| 544 |
1994 |
C/12/94 |
New Methods for Quality Assurane in Metal Forming |
T. Raappana; E. Keranen; T. Piironen; E. Kiuru |
12 |
| 545 |
1994 |
C/13/94 |
Determination of Sheet Metal Forming limits Using the Marciniak Double Blank Method and Computer Vision Based Strain Measurement |
K. Albrektsen |
9 |
| 546 |
1994 |
C/14/94 |
DSMS-Automated Strain Measurement in Sheet Metal Forming |
S.D. Antunes |
11 |
| 547 |
1994 |
C/16/94 |
Interactions of Lubricants and Zinc Coatings |
J. Schey |
12 |
| 548 |
1994 |
C/17/94 |
Mechanisms Influencing the Stability of the Friction Conditions During Press Forming Operations |
E. Schedin |
9 |
| 549 |
1994 |
C/18/94 |
Research on Correlation Between Basic Formabilities and Drawability in China |
X. Cheng; Y. Yan; S. Hu |
11 |
| 550 |
1994 |
C/19/94 |
Multi Pass Friction Tests on Zinc Coated Sheet to Simulate Galling Behaviour |
C.M. Dane |
11 |
| 551 |
1994 |
C/20/94 |
Analysis of Formability Descriptors |
M.J.M. Barata Marques; R.M.S.O. Baptista |
10 |
| 552 |
1994 |
C/21/94 |
A Combined Physical and Numerical Simulation of Tool Performance in Conventional Deep-Drawing Operations |
J. Mortensen; J. Dirks; P. Christensen |
8 |
| 553 |
1994 |
C/22/94 |
Intensive Ultrasound Factor in Tribological Application of Thin Sheet Deep Drawing |
T. Donics |
11 |
| 554 |
1994 |
C/23/94 |
The Experimental Estimating of the Draw Bead Reaction and Its Effects on the Sheet Metal Forming |
O. Szabadits |
6 |
| 555 |
1994 |
C/24/94 |
Development of Testing Equipment for Sheet Metal Forming Analysis |
J.F. Duarte; A.D. Dos Santos; A. Barata da Rocha |
14 |
| 556 |
1994 |
C/25/94 |
Progress in Low Volume Sheet Metal Forming |
T. Johannisson |
10 |
| 557 |
1994 |
C/26/94 |
Computer Aided Process Planning of Sheet Metal Forming Processes |
M. Tisza; P. Racz |
12 |
| 558 |
1994 |
C/27/94 |
Computer Aided Modelling of the Deep-Drawing Process |
A. Hrivnak; E. Evin |
10 |
| 559 |
1994 |
C/28/94 |
On-Line detection of the Material Flow in the Deep Drawing Process as a Basis for an Evaluation of the Yield Stress in the Flange |
E. Doedge; M. Schroeder |
11 |
| 560 |
1994 |
C/29/94 |
Plastic Bending of Anisotropic Sheet Metals |
Z. Tan; C. Magnusson; B. Persson |
11 |
| 561 |
1994 |
C/30/94 |
Numerical Simulation of Sheet Metal Forming Processes by Adaptive Bi-Section Refinement |
D.Y. Yang; I.S. Song; D.J. Yoo |
10 |
| 562 |
1994 |
C/31/94 |
Stress Analysis for Off-Axes Solicitations in Drawing Operations |
R. Arrieux; T. Nguyen Nhat |
12 |
| 563 |
1994 |
C/32/94 |
Different Tool Dexcriptions Used in the Simulation of 3D Forming Processes |
A. Dias Dos Santos; J.F. Duarte; A.B. Da Rocha |
11 |
| 564 |
1994 |
C/33/94 |
Prediction Methods for Ductile Sheet Metal Failure using FE-Simulation |
P. Hora; T. Longchang; J. Reissner |
13 |
| 565 |
1994 |
C/34/94 |
Instabilities in Sheet Metal Forming Analysed with Explicit Finite Finite Element Methods |
K.B. Nielsen; J. Danckert |
12 |
| 566 |
1994 |
C/35/94 |
Numerical Simulation and Experimental Evaluation of the Modifications of Material Properties in a Drawbead |
P. Wouters; G. Monfort; J. Defourny |
13 |
| 567 |
1994 |
C/36/94 |
Deepdrawability of a Round Cylindrical Cup |
J.A.H. Ramaekers; A. De Winter; M.W.H. Kessels |
10 |
| 568 |
1994 |
C/37/94 |
The Application of Computer Models and Automated Strain Measurements in the Solving of Shet Metal Forming Problems |
N.A.J. Langerak |
12 |
| 569 |
1994 |
C/38/94 |
Numerical Dynamics for the Simulation of Deep-Drawing |
M. Jean; F. Jourdan; B. Tathi |
11 |
| 570 |
1994 |
C/39/94 |
3-D FEM Analysis of Strain Path and Fracture Limit in Sheet Forming Processes of Simple Model Shells |
T. Yoshida; K. Hashimoto; M. Usuda |
11 |
| 571 |
1994 |
C/40/94 |
Advanced Finite Element Models for Analysis of Industrial Sheet Forming Processes |
J. Rojek; C. Garcia Garino; E. Onate |
12 |
| 572 |
1994 |
C/41/94 |
A New Efficient Finite Element Model of Shell With Only Three Degrees of Freedom Per Node. Application to Industrial Deep Drawing Test |
G. Rio; B. Tathi; H. Laurent |
12 |
| 573 |
1994 |
C/42/94 |
Theoretical and Experimental Research in Formability on Deep-Drawing Steel Sheets in Pulsatory Straining |
D. Banabic; I.R. Dorr |
6 |
| 574 |
1994 |
C/43/94 |
Automobile Aluminum Panel Stamping Mass Production Technology |
A. Sato; S. Nakamura; Y. Tomioka |
12 |
| 575 |
1994 |
C/44/94 |
The Design of an Optimum Binder Force System for Improving Sheet Metal Formability |
Y.W. Wang; S.A. Majlessi |
12 |
| 576 |
1994 |
C/45/94 |
Effects of Control of Local Blank Holding Forces on Deep Drawability of Square Shell |
A. Murata; M. Matsui |
10 |
| 577 |
1994 |
C/46/94 |
Superplastic Sculpture: Making Re-Entrant Shapes Using Preforming and Ceramic Shell Dies |
P.S. Bate; D.J. Barrett; V.N. McDonagh; S. Jones; C.B. Ponton |
11 |
| 578 |
1994 |
C/47/94 |
Improvement of Shape-Flexibility by Controlling the State of Plastic Strain |
K. Fukutomi; K. Kunitake; M. Marayuma; M. Kudo; T. Nagamitsu |
9 |
| 579 |
1994 |
C/48/94 |
Development of Screed's Manufacturing |
L. Madle |
9 |
| 580 |
1994 |
C/49/94 |
Shape Accuracy and Parameters Influencing the Shape Accuracy Using Conventional and Hydromechanical Deep Drawing |
J.F. Andersen |
9 |
| 581 |
1994 |
C/50/94 |
Improvement of Forming Height and Stability of Aluminum Parts Using Active Binder Control |
J. Cao; R. Bakkerstuen; P. Jalkh; M.C. Boyce; D.E. Hardt |
12 |
| 582 |
1996 |
C/1/96 |
Forming Technology and Sheet Materials for Weight Reduction of Automobile |
H. Hayashi |
19 |
| 583 |
1996 |
C/2/96 |
Light Car Wheels in High Strength Steel |
G. Hibon; G. Marron; P. Patou |
14 |
| 584 |
1996 |
C/3/96 |
Weight Reduction Technology by Laser Irradation for Body Panels |
K. Tamada; A. Sato; N. Nakagawa |
8 |
| 585 |
1996 |
C/4/96 |
Effects of Work Hardening Rate on Formability of Recently Developed DDQ Steels |
C. Gusek; W. Bleck; W. Dahl |
10 |
| 586 |
1996 |
C/5/96 |
Improvement of Dent Resistance of Auto Body Panels Taking Advantage of Strain Hardening Properties of Steel Sheets |
B. Dauby; P. Magain; R. Kergen; F. Beco; S. Vandierendonck; M. Van Overmeire; Vereecken; J |
10 |
| 587 |
1996 |
C/6/96 |
Designing Stamped Parts in Hot Rolled Steel Sheets |
G. Hibon; G. Marron; P. Patou |
12 |
| 588 |
1996 |
C/7/96 |
In-Process Control of Blank Holder Force in Axi-symmetric Deep Drawing with degressive gas Springs |
L. Gunnarsson; N. Asnafi; E. Schedin |
12 |
| 589 |
1996 |
C/8/96 |
Development of a Square-Cup Deep Drawing Simulator with Cellularly Divided Blank Holder Control System |
K. Manabe; M. Yang; T. Teramae; H. Nishimura |
8 |
| 590 |
1996 |
C/9/96 |
Finite Element Simulation of the Closed-Loop Control of the Blank-Holder Force in Deep-Drawing |
M. Traversin; R. Kergen; P. Harlet |
10 |
| 591 |
1996 |
C/10/96 |
An Improved Manufacturing Process in Sheet Metal Forming |
S.A. Saeedy; A. Majlessi |
12 |
| 592 |
1996 |
C/11/96 |
Elastoforming: An Industrial Process for the Forming of Extra-thin Sheets |
M. Munier; X. Dupont; M. Dittlo |
10 |
| 593 |
1996 |
C/12/96 |
Deep Drawing with Flexible Die |
J. Danyi; F. Vegvari |
10 |
| 594 |
1996 |
C/13/96 |
Viscous Fluid Forming of Tubes |
M. Kral; S. Borji |
6 |
| 595 |
1996 |
C/14/96 |
Analysis of Drawing without Blankholder of Rotational Cups from Non-Circular Blanks |
Z. Kampus; K. Kuzman |
8 |
| 596 |
1996 |
C/15/96 |
A General Review of CAD/CAM/CAE Applications in Sheet Metal Forming |
M. Tisza |
10 |
| 597 |
1996 |
C/16/96 |
Utilisation of Computer Simulation in Skoda Car Factory |
Z. Buchar; P. Chaloupecky |
8 |
| 598 |
1996 |
C/17/96 |
Modelling of Sheet-Metal Forming using Stress-Line Methods |
K. Kardos; F. Boor |
10 |
| 599 |
1996 |
C/18/96 |
Sheet Metal Forming: State-of-the-Art of the Application Methodology and Simulation Streamlining |
F. El-Khaldi; D. Lefebvre; A. Mehrez; A. Heath; T. Hayashi; R. Joshi; L. Taupini; R. Bernardi; O. Ogura |
16 |
| 600 |
1996 |
C/19/96 |
Deep Drawing Simulation of Vibration Damping Steel Sheets |
E. Finckenstein; L. Kessler; E.J. Drewes; V. Steininger |
16 |
| 601 |
1996 |
C/20/96 |
A New Sheet Metal Formability Estimation System Using Three-Dimensional Finite Element Method |
K. Hashimoto; T. Yoshida; M. Usuda |
10 |
| 602 |
1996 |
C/21/96 |
Computationally Efficient Elasto-Plastic Implicit Finite Element Analysis for Complicated Sheet Metal Forming Processes |
J.W. Yoon; D.Y. Yang |
14 |
| 603 |
1996 |
C/22/96 |
Finite Element Method for Complex Behaviour Solid Analysis |
C. Maier; M. Teodorescu; M. Banu |
10 |
| 604 |
1996 |
C/23/96 |
Development of a Fast Design and Trouble-Shooting FEM in Sheet Metal Forming |
S. Liu; T. Kolodziejski; A. Assempoor; T. Aboutour; W. Cheng |
12 |
| 605 |
1996 |
C/24/96 |
Optimization of the Draw Die Profile with Regard to Wear Using the FEM |
F. Damborg; M.R. Jensen; K.B. Nielsen; J. Danckert |
10 |
| 606 |
1996 |
C/25/96 |
Finite Element Simulation of the Plane Strain Punch Stretching Test |
Y.H. Kim; S.P. Chundal |
10 |
| 607 |
1996 |
C/27/96 |
Prediction of Necking of Sheet Metal Forming from Finite Element Simulations and Computations Based on Crystalline Plasticity |
N. Boudeau; R. Kopp |
10 |
| 608 |
1996 |
C/29/96 |
A New Possibility of Modelling of Strain-Hardening and Anisotropy |
F. Boor |
10 |
| 609 |
1996 |
C/30/96 |
Formability of Tailored Blanks from Steel and Aluminium Alloys |
F. Vollertsen; M. Schultz; N. Geiger |
10 |
| 610 |
1996 |
C/31/96 |
Formability Issues for Tailored Blanks |
J.M. Van Der Hoeven; K. Rubben; F. Lambert; I. De Rycke; J. Scheers |
10 |
| 611 |
1996 |
C/32/96 |
Effect of Chemical Composition, Mechanical Properties and Thickness of Base Steels on Formability of Laser-Welded Blanks |
Y. Yamasaki; M. Yoshida; S. Kabasawa; M. Ono |
10 |
| 612 |
1996 |
C/33/96 |
Formability Characterization of Aluminum Sheets used in Automotive Industry |
J. Duarte; A. Rocha; B. Bacroix; J. Gracio |
10 |
| 613 |
1996 |
C/34/96 |
Formability of Hot Rolled High Strength Steel Sheets for Automotive Suspension Parts |
N. Komatsubara; Y. Hirose; S. Nomura; C. Sudo |
10 |
| 614 |
1996 |
C/35/96 |
Deep Drawability of Low Carbon Steel |
A.B. Lopes; J.J. Gracio |
10 |
| 615 |
1996 |
C/36/96 |
Effect of Material Inhomogeneity of Formability of Copper and Brass Sheets |
F. Stachowicz |
10 |
| 616 |
1996 |
C/37/96 |
Mathematical Model of the Forming Limit Diagrams Using the New Hills Yield Criterion |
D. Banabic |
8 |
| 617 |
1996 |
C/38/96 |
The Strain Path Change and Stretch Formability of an Al-Mg-Si Alloy Sheet |
A. Yuguo |
10 |
| 618 |
1996 |
C/39/96 |
A Shapebility Testing of the Counter-Pressed Deep Drawing |
GY Ziaja |
8 |
| 619 |
1996 |
C/40/96 |
A Strip Reduction Test for Measurement of Lubricity in Ironing |
J.L. Andreason; N. Bay |
10 |
| 620 |
1996 |
C/41/96 |
Bake Hardening Effect in Components |
M. Blaimschein; K. Radlmayr; A. Pilcher; E. Till; P. Stiaszny |
14 |
| 621 |
1996 |
C/42/96 |
Hole Expansion in Hot Rolled Steels |
G.H. Strijbos; R. Boesenkool |
8 |
| 622 |
1996 |
C/43/96 |
Parameters Influencing Stamping Behaviour of Coated Sheets |
J. Billy; F. Simcak; B. Stefan; J. Zaboj |
10 |
| 623 |
1996 |
C/44/96 |
Shape Accuracy of the Stretch-Bent Strips |
O. Szabadits |
8 |
| 624 |
1996 |
C/45/96 |
Some Frictional Aspects of Aluminum in Sheet Metal Forming |
W.C. Emmens; F. Schoepen |
10 |
| 625 |
1996 |
C/46/96 |
Effects of Strength and Surface Roughness of Steel Sheets on Frictional Behaviour During Sheet Forming |
T. Kato; E. Iizuka; O. Furukimi; T. Obara |
8 |
| 626 |
1996 |
C/47/96 |
Prelubs: Advantages and Drawbacks |
A. Col; P. Terreaux |
10 |
| 627 |
1996 |
C/48/96 |
The Frictional Properties of Galvannealed Steel Sheets |
J. Scheers; B.C. De Cooman; M. Vermeulen |
12 |
| 628 |
1996 |
C/49/96 |
Modelling of Friction Ratios in Deep-Drawing Process |
A. Hrivnak; E. Evin |
6 |
| 629 |
1996 |
C/50/96 |
Binder Wrap Analysis Considering Gravity, Contact and Friction |
D.J. Yoo; G. Jun; J.M. Lee |
8 |
| 630 |
1996 |
C/51/96 |
Study About the Nature of the Friction-Lubrication Process During the Deep Drawing of Thin Sheets |
M. Teodorescu; G. Frumusanu; L. Teodorescu |
6 |
| 631 |
1998 |
C/1/98 |
Advanced Forming Technologies |
K.Siegert, S. Wagner |
27 |
| 632 |
1998 |
C/2/98 |
Development of a high pressure liquid lubrication method for press forming |
Y. Yamasaki, M. Yoshida |
12 |
| 633 |
1998 |
C/3/98 |
Improvement in forming limit of square shell by point beading |
A. Murata, K. Tamada |
12 |
| 634 |
1998 |
C/4/98 |
FEA assisted body-in-white manufacturing feasibility study |
S-D Liu |
12 |
| 635 |
1998 |
C/5/98 |
Modelling the deep drawing of process optimized blanks |
F. Vollersten, A. Hofmann |
10 |
| 636 |
1998 |
C/6/98 |
Non-conventional methods of deep drawing of tailored blanks |
T. Pepelnjak, Z. Kampus, K Kuzman |
12 |
| 637 |
1998 |
C/7/98 |
For an optimized combination of steels and welding process before forming |
P. Wouters, G Monfort, J. Defourny |
14 |
| 638 |
1998 |
C/8/98 |
Rapid Design and Prototyping |
U. Dworzak |
10 |
| 639 |
1998 |
C/9/98 |
Integration of knowledge based system and FEM simulation in deep-drawing processes |
M. Tisza |
10 |
| 640 |
1998 |
C/10/98 |
Coupled sheet metal forming and fatigue simulation |
Y. LeRoch, J.L. Duval, El Mouatassim, E. Di Pasquale |
10 |
| 641 |
1998 |
C/11/98 |
Deep drawing simulation of tailored blanks |
A.C. van den Berg, T. Meinders, B. Stokman |
12 |
| 642 |
1998 |
C/12/98 |
Application of ductile fracture criteria to bending under tension |
F.F. Damborg, R.H. Wagoner, K. B. Nielsen, J. Danckert |
12 |
| 643 |
1998 |
C/13/98 |
Forming limit diagrams for stamping formability prediction |
Z. Buchar |
8 |
| 644 |
1998 |
C/14/98 |
Process monitoring and sheet metal formability in stamping of box-shaped components |
G. Ekstrand, T. Hamman |
14 |
| 645 |
1998 |
C/15/98 |
A comarison of different blank-holder force control principles based on the cup test |
R. Kergen |
10 |
| 646 |
1998 |
C/16/98 |
Environmentally friendly manufacturing of tailor made blanks |
A. de Winter |
12 |
| 647 |
1998 |
C/17/98 |
Friction of aluminum in deep drawing |
W.C. Emmens |
12 |
| 648 |
1998 |
C/18/98 |
Influence of sliding direction and sliding speed on the micro-hydrodynamic lubrication component of aluminum mill-finish sheets |
F. Raharijaona, P. Belliard, X. Roizard, J. von Stebut |
10 |
| 649 |
1998 |
C/19/98 |
Influence of surface morphology on frictional behaviour in sheet metal forming |
M. Jonasson |
14 |
| 650 |
1998 |
C/20/98 |
Effect of surface roughness on galling behavior |
E. Iizuka, C. Fujinaga, T. Hira, M. Morita, O. Furukimi |
10 |
| 651 |
1998 |
C/21/98 |
Assessment of thermal effect during the friction test |
L. Penazzi, C. Rayssiguier, C. Boher, C. Levaillant |
10 |
| 652 |
1998 |
C/22/98 |
Friction in sheet metal forming- Comparison to a drawbead strip test |
L. Gunnarsson, T. Floren |
10 |
| 653 |
1998 |
C/23/98 |
Study of the frictional behaviour of steel sheet surfaces during deep drawing by use of Design of Experiments |
J. Scheers, D. De Mare |
12 |
| 654 |
1998 |
C/24/98 |
A study of the influence of EBT-textured steel sheets on the frictional behaviour in a strip test |
A. Wihlborg, L. Gunnarson |
10 |
| 655 |
1998 |
C/25/98 |
Experimental derermination of forming limit diagrams using a method of digital picture |
S. Mguil, P. Clerc, F. Morestin, M. Brunet |
10 |
| 656 |
1998 |
C/26/98 |
Recent trend in development of sheet materials for automotive use |
H. Hayashi |
16 |
| 657 |
1998 |
C/27/98 |
How to compensate for the elastic strains when using automaitc tensile test equipment |
J. Danckert, K.B. Nielsen |
12 |
| 658 |
1998 |
C/28/98 |
Implementation of the Gurson/Twergaard Void Growth Model and Computational Examples |
T.G. Faurholdt |
14 |
| 659 |
1998 |
C/29/98 |
Determination of yield loci form cross tensile tests assuming various kinds of yield criteria |
D. Banabic, W. Muller, K. Pohlandt |
8 |
| 660 |
1998 |
C/30/98 |
Producibility assesment of aluminum automotive panels |
E. Chu, K. Matsui, H.R. Zonker, K.N. Shah, S. Yoshizawa |
12 |
| 661 |
1998 |
C/31/98 |
Instantaneous mechanical properties and forming limits of aluminium alloy sheets |
F. Stachowicz |
10 |
| 662 |
1998 |
C/32/98 |
Study on wrinkling limit diagram of anisotropic sheet metals |
Y-J Son, Y.S. Kim |
14 |
| 663 |
1998 |
C/33/98 |
Description of strain-induced martensitic phase transformation in metastable austenitic steels for the simulation of deep drawing processes at non isothermal conditions |
A. Hansel, P. Hora, J. Reissner |
12 |
| 664 |
1998 |
C/34/98 |
The influence of the testing temperature on mechanical properties and formability of cold-rolled low and high alloyed TRIP-steels |
S. Kranz, W. Bleck, K. Papamantellos |
8 |
| 665 |
1998 |
C/35/98 |
The comparison in dent resistance between high strength steel with excellent formability and bake-hardenable steel |
Y. Hirose, M. Nakata, N. Kojima, N. Mizui |
8 |
| 666 |
1998 |
C/36/98 |
Comparison of dent resitance and shape fixability between bake-hardenable type and high R-value type high strength sheet steel |
Y. Omiya, T. Kase, I. Tsukatani, Y. Okano |
8 |
| 667 |
1998 |
C/37/98 |
Determination and application of the forming limits for deep drawing processes with organic coated steel sheets by use of the FEM |
Ch. Filthaut, L. Kebler, F.J. Lenze, von Finkenstein |
10 |
| 668 |
1998 |
C/38/98 |
FEA and theoretical FLD based on new constitutive equation for estimation of sheet metal forming |
T. Yoshida, Y. Kuriyama, M. Usuda, K. Ito |
10 |
| 669 |
1998 |
C/39/98 |
A new method for predicting FLC |
F. Cayssials |
8 |
| 670 |
1998 |
C/40/98 |
Using the "3G" theory of plasticity for the prediction fo necking in deep drawing operations |
A. Haddad, P. Vacher, R. Arrieux, G. Monfort |
8 |
| 671 |
1998 |
C/41/98 |
Microstructural gradients in conventional and hot sheet forming |
P. Bate, D.J. Barrett, S. Rhaipu, H. Schofield, J.Q. Jiang |
12 |
| 672 |
1998 |
C/42/98 |
Recent Developments in Inverse Simulation of Sheet Metal Forming |
J.L. Duval, E. Di Pasquale, V. Rigaud |
10 |
| 673 |
1998 |
C/43/98 |
Study on complex forming of Al-Mg alloys |
M.C. Butuc, J.J. Gracio, J. Ferreira Duarte, A. Barata da Rocha |
8 |
| 674 |
1998 |
C/44/98 |
Dimensional inaccuracy in draw-bending process of aluminium alloy sheets |
S. Bac, F. Stachowicz |
6 |
| 675 |
1998 |
C/45/98 |
Improvement of formability by laser quench method |
J. Ogawa, K. Tamada, A. Sato |
8 |
| 676 |
1998 |
C/46/98 |
Improvement of the tailored blank stamping by using a control and localisation of the blank-holder |
D. Ninforge, J. Dawance |
10 |
| 677 |
1998 |
C/47/98 |
Production of flexible roller parts-First results in deep drawing |
A. Evert, R. Kopp |
8 |
| 678 |
2000 |
C/1/00 |
Simulated and Experimental Deep Drawing of Alloy Tailor Welded Blanks |
Y. Lee, M.J. Worswick, M. Finn, W. Christy, M. Jain |
8 |
| 679 |
2000 |
C/2/00 |
The Formability of Tailor-Welded Blanks Depending on Welding Methods and Material Combinations |
Elisabeth Sagstrom, Hans Larsson, Bengt Nilsson, Boel Wadman |
8 |
| 680 |
2000 |
C/3/00 |
An Industrial Application of Specific Forming Limit Curves for Tailor Welded Blanks |
Franck Cayssials |
6 |
| 681 |
2000 |
C/4/00 |
Hydroforming of Tailored Tubes |
A. Eichhorn, S. Motsch |
10 |
| 682 |
2000 |
C/5/00 |
Analysis of the Tube Formability in Perspective of Tube Hydroforming |
R. Kergen, J.C. Lescart, P. Duroux |
10 |
| 683 |
2000 |
C/6/00 |
Effects of Material Properties and Process Parameters On Deformation Behaviour of Tube In Hydroforming |
T. Yoshida, Y. Kuriyama |
10 |
| 684 |
2000 |
C/7/00 |
On Path Dependence of Tubular Hydroforming |
Z. Cedric Xia, Sing C. Tang |
8 |
| 685 |
2000 |
C/8/00 |
Finite Element Simulation of Expansion of Tubes in Hydroforming |
Kuo-Kuang Chen |
8 |
| 686 |
2000 |
C/9/00 |
Membrane Deformation When Deep Drawing With Multiple Elastomer Membranes |
R. Breede, F. Vollertsen |
8 |
| 687 |
2000 |
C/10/00 |
Development of High Tensile Strength Steel with Good Press-Formability And Shape Control Technology |
Yoshiaki Nakazawa, Yozo Hirose, Masahiro Nakata and Naomitsu Mizui |
10 |
| 688 |
2000 |
C/11/00 |
Material Window Database for Stamping Analysis |
Yanwu Xu, Xiaoming Chen |
9 |
| 689 |
2000 |
C/12/00 |
Effect of Strain-Rate Exponents on Neck Shape |
William F. Hosford |
7 |
| 690 |
2000 |
C/13/00 |
The Impact of Lubricant Buffering on the Operating Window of Deep Drawing Processes |
R. ter Haar, E.H. Atzema |
8 |
| 691 |
2000 |
C/14/00 |
The Origin Of Panel Twist: A Complex Function Of Shape, Process And Material |
A. Col, S. Giffard-Bouvier, F. Moussu |
8 |
| 692 |
2000 |
C/15/00 |
Friction Model That Predicts Springback |
Klaus W. Blumel, Peter Ufermann |
10 |
| 693 |
2000 |
C/16/00 |
Optimization of Tool Configuration for Press Forming of High Strength Steel Sheets by Elasto-Plastic Analysis |
Masaki Urabe, Yamasaki Yuji, Yoshihiro Hosoya |
9 |
| 694 |
2000 |
C/17/00 |
Effect of Lankford Value on Square Cup Drawability |
C. Kami, K.Okuda, Y. Kawabata, T. Hira, A. Tosaka, O. Furukimi |
6 |
| 695 |
2000 |
C/18/00 |
Inelastic Effects On Springback In Metals |
R. Cleveland and A.K. Ghosh |
17 |
| 696 |
2000 |
C/19/00 |
A Hardening Rule for Steel Combining Strain and Strain Rate Hardening and its Application in Stamping |
Bernard S. Levy, Benda Yan, J.M. Stringfield |
14 |
| 697 |
2000 |
C/20/00 |
Improvement of Fatigue Strength of High Tensile Strength Steel Sheet with a Pierced Hole By Optimizing of Coining Conditions and Material |
M. Nakaya, T. Shiogama, T. Soshiroda, Y. Okano |
6 |
| 698 |
2000 |
C/21/00 |
Experiences in the Use of a Combined Drawing and Stretching Test for Assessing the Formability of Sheet Steel Products |
Louisa Elliott, Mike Boyles |
6 |
| 699 |
2000 |
C/22/00 |
Analysis and Closed Loop Control of Deep-Drawing Processes with On-Line Measurement of the Material Flow |
Eckart Doege, Bernd Griesbach, Torsten Mende |
9 |
| 700 |
2000 |
C/23/00 |
On Elastoplastic Analysis of Flange Wrinkling of Aluminum Cup |
E. Chu |
8 |
| 701 |
2000 |
C/24/00 |
Experimental and Numerical Studies of Multiple Bending-Unbending Springback Processes |
S.-D. Liu, S. Jiang, M.Garnett |
10 |
| 702 |
2000 |
C/25/00 |
Conventional Deflection of Non Deflectable Surfaces within CAD/CAM/CAE Environment |
Dr. Ferenc Boor, Dr. Karoly Kardos |
8 |
| 703 |
2000 |
C/26/00 |
Generalisation of Material Laws For Sheet Metals |
Tibor Fulop, Miklos Tisza |
8 |
| 704 |
2000 |
C/27/00 |
Proposal of A New Anisotropic Yield Criterion |
Dorel Banabic, T. Balan, D.-S. Comsa, W. Muller, K. Pohlandt |
4 |
| 705 |
2002 |
C/01/02 |
Scientific and Technological Strategy of Sheet Metal Forming in the 21st Century |
Hisashi Hayashi |
8 |
| 706 |
2002 |
C/02/02 |
A Simple Method for Strengthening and Decorating of Sheet Metals |
Katsuhiko Yamaguchi, Roy C. Sagrado, Norio Takakura, Takashi Iizuka |
10 |
| 707 |
2002 |
C/03/02 |
Formability of Wavy Sheet Created by Buckling |
Nobukazu Hayashi, Masanori Kobayashi |
6 |
| 708 |
2002 |
C/04/02 |
Forming of Long Pure Titanium Cups by Multi-Stage Deep Drawing |
Ken-ichiro Mori, Yasunori Harada, Takuji Murao |
8 |
| 709 |
2002 |
C/05/02 |
Adaptability of Thermal (Plasma)-Spray-Coated Dies and Other Dies for Deep-Drawing of Titanium Sheet |
Manabu Gotoh, Minoru Yamashita, Joji Satoh, Fujio Okubo, Takuji Murao |
10 |
| 710 |
2002 |
C/06/02 |
Modeling of Deep Drawing of Stainless Steel |
T. Manninen, J. Larkiola, A.S. Korhonen |
8 |
| 711 |
2002 |
C/07/02 |
Evaluation of Press Forming Severity and Application for Die Design by One-step-FEM Analysis |
Genki Mano, Yoshifumi Yoshisato, H.Yanase, M.Hayase, Masao Matsui, Koe Nakajima |
10 |
| 712 |
2002 |
C/08/02 |
The Improvement of Hydroforming Simulation Performance |
Susumu Takahashi, Kousduke Terada |
10 |
| 713 |
2002 |
C/09/02 |
Theorethical and Experimental Analysis of the Multi-step Forming of a Rear Seat Part |
Rui M.S.O. Baptista, Beatriz C.J. Siva |
8 |
| 714 |
2002 |
C/10/02 |
Development of Shape-Fixing Press Forming Technology for High Strength Steel Sheet |
Masahiro Nakata, Yozo Hirose, Nobuyuki Nakado,Takahisa Ogawa |
10 |
| 715 |
2002 |
C/11/02 |
Spring-back Simulation in Sheet Metal Forming, Considering Material Non-Linearity during Unloading |
H. Tsutamori, N. Iwata, N. Suzuki |
8 |
| 716 |
2002 |
C/12/02 |
Effects of Material Properties on Shape-Fixability and Shape Control Techniques in Hat-Shaped Forming |
Tomohisa Katayama, Tohru Yoshida, Akihito Sato |
10 |
| 717 |
2002 |
C/13/02 |
FLC's: Past, Present and Future |
Alain Col |
20 |
| 718 |
2002 |
C/14/02 |
Prediction of Forming Limit Diagram (FLD) and Equivalent Work Hardening Index of Sheet Metals |
Liwei Gu, Akinori Tanaka, Kenji Tanaka, Koe Nakajima |
10 |
| 719 |
2002 |
C/15/02 |
Effects of a Laser Welded Line in Forming Limit Diagrams of Tailored Blanks |
Koji Hashimoto, Yukihisa Kuriyama |
8 |
| 720 |
2002 |
C/16/02 |
Study on Control of Non-Uniform Deformation of Tailor-Welded Blanks |
S.H. Zhang, Y.Xu, Z.T. Wang, W.L. Zhou, L.X. Zhou |
8 |
| 721 |
2002 |
C/17/02 |
Proposal of Press Formability Evaluation Method of Steel Sheet in Actual Automotive Panels |
Yoshikiyo Tamai, Kiyoshi Nonomura |
6 |
| 722 |
2002 |
C/18/02 |
Effects of Material Properties and Forming Conditions on Stretch Flange Drawing |
Kazuo Uematsu, Yashiaki Nakzawa, Masahiro Nakata, Yozo Hirose |
10 |
| 723 |
2002 |
C/19/02 |
Experiences in Implementation of Computer Aided Tools in Small and Medium Sized Tool Making Companies |
Karl Kuzman, Gašper Gantar, Luka Butolin |
8 |
| 724 |
2002 |
C/20/02 |
Development of a CAPP System for Lubrication Selection in Sheet Metal Forming |
Miklós Tisza |
8 |
| 725 |
2002 |
C/21/02 |
An Intelligent Process Control of Punch Speed and Blank Holder Force in Deep-Drawing |
Ken-ichi Manabe, Tetsuya Yagami, Shoichiro Yoshihara, Hiroshi Koyama |
8 |
| 726 |
2002 |
C/22/02 |
Characterizations as Automotive Parts of Advanced High Strenth Steels |
Kenichi Watanabe, Takayuki Yamano, Jiro Iwaya |
10 |
| 727 |
2002 |
C/23/02 |
Development of High-Strength Steel with Fine Grain Structure for Exposure Panel |
Toshiaki Urabe, Fusato Kitano, Yoshihiko Ono, Takeshi Fujita, Yuji Yamasaki, Yoshihiro Hosoya |
10 |
| 728 |
2002 |
C/24/02 |
FEM Analysis of Crashworthiness of Hot-Rolled Sheet Steel with Excellent Bake Hardenability in Tensile Strength |
Jiro Hiramoto, Shinnjiro Kaneko, Takaaki Hira, Kei Sakata, Hideo Abe |
6 |
| 729 |
2002 |
C/25/02 |
Alternative 2D Surface Topography Parameters for Optimising Friction Behaviour of Zinc Coated Sheets |
A.C. Carcel, C. Ferrer, M.A. Perez Puig |
10 |
| 730 |
2002 |
C/26/02 |
Surface Topography Eveolution of Zinc Coated Steel Sheets under Boundary Lubrication |
A.C. Carcel, M.A. Perez Puig, C. Ferrer |
10 |
| 731 |
2002 |
C/27/02 |
Results of Round Robin Test with the GDDGR to Characterize Surfaces of Cold Rolled Steel Sheets with Defferent Textures under Production Conditions by Measuring the Parameters Ra and RPc |
Gregor Steinbeck, Hans-Gerd Weyen |
10 |
| 732 |
2002 |
C/28/02 |
Separate Measurement of Frictional Coeffients on Die Profile and Flange Part in Cylindrical Cup-Drawing |
Manabu Gotoh, Minoru Yamashita, Jun Suzuki |
10 |
| 733 |
2002 |
C/29/02 |
Tribo-Simulator for Iteritive Processes in Sheet Metal Forming |
Tamotsu Nakamura, Shigekazu Tanaka, Kunio Hayakawa, Haruki Imaizumi, Hideo Sano, Munenori Sugisawa, Masayoshi Muraki, Junichi Shibata |
10 |
| 734 |
2002 |
C/30/02 |
Hot Melt Dry Film Based Lubrication, Quantitative Model for Coefficient of Friction |
Gert-Jan Streefland |
10 |
| 735 |
2002 |
C/31/02 |
Hydromechanicla Forming of Trunk Lid Outer |
Johnny Ocklund, Nader Asnafi, Hiroyuki Amino, Trent Maki |
10 |
| 736 |
2002 |
C/32/02 |
Tubular Hydroforming of Side Members and Crash Beams - A Study from the Perspective of Volvo Cars |
Nader Asnafi, Johnny Ocklund, Gunnar Lassl |
10 |
| 737 |
2002 |
C/33/02 |
Effects of Material Properties on Formability in Hydroforming of ERW Tubes |
Osamu Sonobe, Yuji Hashimoto, Takaaki Hira, Hideo Abe |
8 |
| 738 |
2003 |
C/1/03 |
Numerical Modelling and Simulation in Sheet Metal Forming: Academic and Industrial Perspectives |
M.Tisza |
10 |
| 739 |
2003 |
C/2/03 |
Sheet Metal Anisotropy at Geometric Modelling of Deep-Drawn Workpieces |
I.Czinege, E. Halbritter, K.Kardos |
10 |
| 740 |
2003 |
C/3/03 |
Benchmark Numisheet on Cup Drawing |
E.H. Atzema |
10 |
| 741 |
2003 |
C/4/03 |
Experimental Study and Simulation of Warm Deep Drawing of Aluminium |
V.Nalewajk, Y.Chastel, J.P.Nauzin |
2 |
| 742 |
2003 |
C/5/03 |
FE Supported Development of a Cooling Ventilator of a Vacuum Cleaning Motor |
G.Gantar, M.Nastran, K. Kuzman, M.Makarovic |
12 |
| 743 |
2003 |
C/6/03 |
Precision Needed for Material Data for Stamping and Hydroforming Simulation |
E.Massoni, Y. Chastel |
10 |
| 744 |
2003 |
C/7/03 |
Standardisation of Forming Limit Curves |
J-L Geoffroy |
14 |
| 745 |
2003 |
C/8/03 |
Effect of Bending Over a Radius on the North American Forming Limit Curve |
D.E. Green, B.S. Levy |
10 |
| 746 |
2003 |
C/9/03 |
Material Data for Aluminum Alloys at High Strain Rates |
Bjorn Andersson, Tor Einar Johnsen |
8 |
| 747 |
2003 |
C/10/03 |
Notion of 'unloading tangent modulus' used to a better prediction of Spring Back |
J-L Geoffroy |
10 |
| 748 |
2003 |
C/11/03 |
Material parameters for the FEM-Simulation - Impact of Advanced Material Models on Forming and Part Properties |
Jörg Gerlach, Lutz Kessler |
10 |
| 749 |
2003 |
C/12/03 |
Certain Aspects of Electromagnetic Forming and Tube Hydroforming Processes |
E. Chu |
10 |
| 750 |
2003 |
C/13/03 |
Numverical and Experimental Investigation into the Hydromechanical Deep Drawing Without a Draw Die |
Lihui Lang, Joachim Danckert, Karl Brian Nielsen |
10 |
| 751 |
2003 |
C/14/03 |
Pre-stretcing, forming, trimming, flanging and cailibration of Hood Outer conducted in the same cycle in a fluid-cell (QUINTUS) press |
Göran Thuresson, Olle Servin, Daniel Bencan, Nader Asnafi, Marlene Jönsson, Keijo hellgren, Tom Johannisson |
7 |
| 752 |
2003 |
C/15/03 |
Incremental Sheet Metal Forming with a High-Speed Water Jet |
Bostjan Jurisevic, Kurt C. Heiniger, Karl Kuzman, Mihael Junkar |
10 |
| 753 |
2003 |
C/16/03 |
Forming of Sheet Metal at an Elevated Temperature |
Elisabeth Sagstrom, Eva Troell, Per Gabrielsson, Lars-Olof Ingemarsson, Ramin Moshfegh, Boel Wadman |
6 |
| 754 |
2003 |
C/17/03 |
Hot Stamping of Quenchable Steels: Material Data and Process Simulations |
L. Garcia Aranda, P. Ravier, Y. Chastel |
9 |
| 755 |
2003 |
C/18/03 |
Process Optimization and Control For Incremental Sheet Metal Forming |
Sanjay Jadhav, Roland Goebel, Werner Homberg, Matthias Kleiner |
7 |
| 756 |
2003 |
C/19/03 |
Fast Small Quantity Production of Sheet Metal Components- A Challenge for Slovene Toolmakers |
Karl Kuzman |
12 |
| 757 |
2003 |
C/20/03 |
Tool Surfaces for Galling-Free Metal Forming |
Emile van der Heide |
18 |
| 758 |
2003 |
C/21/03 |
Fluid-Cell Forming Tools Produced by Different Rapid Prototyping Methods |
Boel Wadman |
10 |
| 759 |
2003 |
C/22/03 |
Lightweight Structure Materials In The Automotive Industry (A Challenge for Sheet Metal Forming) |
Siegfried Kluge |
9 |
| 760 |
2003 |
C/23/03 |
Knowledge, Experiences and Numerical Sheet Metal Process Simulations- A Basis for Fast Reliable Preparation of an Offer |
Andrej Stepišnik, Karl Kuzman |
7 |
| 761 |
2003 |
C/24/03 |
By Interconnecting and Integration of Knowledge Toward a New Technological Quality |
Janez Poje, Erik Aagaard, Boris Štok, Nikolaj Mole |
8 |
| 762 |
2003 |
C/25/03 |
Springback Behaviors of High Strength Steel Sheets in Forming of Autobody Parts |
Hishashi Hayashi |
8 |
| 763 |
2003 |
C/26/03 |
3DS Project Results Concerning Springback Experiments |
Alain Col, Abel Santos |
9 |
| 764 |
2003 |
C/27/03 |
Manufacturing of Autobody Sheets with Improved FormStiffness by Cold Rolling |
Wolfgang Rasp |
11 |
| 765 |
2003 |
C/28/03 |
Deep Drawing of Laser Welded Aluminum-Steel/ Aluminum-Titanium Tailored Blanks |
Frank Vollertsen, Michael Kreimeyer |
10 |
| 766 |
2003 |
C/29/03 |
Three Sheet Metal Hydroforming Methods: Their Influence on Process-Related Component Properties |
Boel Wadman, Elisabeth Sagström, Ramin Moshfegh, Håkan Thoors, Tomas Jansson, Bengt Nilsson |
10 |
| 767 |
2003 |
C/30/03 |
Fundamental Research of Formability of Aluminum Alloys for Autobody Use |
Hisashi Hayashi |
1 |
| 768 |
2003 |
C/31/03 |
Behavior of Tailor rolled Blanks in Deep-Drawing Process |
R. Kopp, C. Wiedner |
10 |
| 769 |
2003 |
C/32/03 |
A Flexible Process for Producing a Novel Cell Structure Using Forming Options of a Modern Turret Punch Press |
M. Lohtander, J.P. Varis, JH. Larkiola and R. Karppi |
7 |
| 770 |
2004 |
C/1/04 |
Final Results of the "3DS" Project |
A. Col, A. Santos |
10 |
| 771 |
2004 |
C/2/04 |
Numerical Simulation of Blankholder Ram Tilting:Effect on the Pressure Distribution in the Blankholder |
M. C. Oliveira, J. L. Alves, L. F. Menezes, A. D. Santos |
10 |
| 772 |
2004 |
C/3/04 |
Design of Ironing Dies |
J. Danckert |
10 |
| 773 |
2004 |
C/4/04 |
Web-Based Application in Sheet Metal Forming |
R. S. Hingole, V. M. Nandedkar, K. Narasimhan |
7 |
| 774 |
2004 |
C/5/04 |
Recent Advances in Industrially Applied Numerically Aided Springback Compensation |
B. Rietman, K. Kose, St. Ohnimus, M. Petzoldt, J. Weiher |
7 |
| 775 |
2004 |
C/6/04 |
Verification of Simulations and Evaluation of Stamping Processes by Forming Analysis |
D. Behring, K. Galanulis, H. Friebe, M. Klein |
10 |
| 776 |
2004 |
C/7/04 |
An Evaluation Method for Springback Behavior of Sheet Metals based on the Stretch Bending Test |
T. Kuwabara, Y. Asano, H. Hayashi |
10 |
| 777 |
2004 |
C/8/04 |
Springback in Flange and Channel Dies with Straight Bend Axis |
B. S. Levy, C. 1. Van Tyne |
9 |
| 778 |
2004 |
C/9/04 |
New Approach for Spring back Compensation in Die Design Application for High Strength Steel |
M. Munier, J.M. Devin, M. El Mouatassim |
9 |
| 779 |
2004 |
C/10/04 |
Springback Simulation - The Last Missing Link for a Complete Forming Simulation |
G. Glanzer, W. Kubli, E. Schonbach, M. Selig |
22 |
| 780 |
2004 |
C/11/04 |
Techniques to improve Springback Prediction Accuracy using Finite Element Analysis |
K. Sato, T. Hira, A. Y oshitake, J. Gerlach, K. Blumel |
9 |
| 781 |
2004 |
C/12/04 |
Springback Simulation in Sheet Metal Forming using Material Formulation based on Combined Isotropic-kinematic Hardening with Elasto-plastic Anisotropy |
A. Krasowsky, W. Schmitt, F. Andrieux, T. Walde, H. Riedel (Germany) |
10 |
| 782 |
2004 |
C/13/04 |
Deep Drawing of Friction Stir Welded Aluminium-Tailored-Blanks |
M. Geiger, M. Merklein, A. Giera |
10 |
| 783 |
2004 |
C/14/04 |
Scattering Parameters is not a Problem anymore for a Robust forming Process |
B. Carleer |
9 |
| 784 |
2004 |
C/15/04 |
Development of Frontside Member by Hydroforming |
K. Iguchi, O. Akutsu, M. Mizumura, T. Niwa, Y. Kuriyama |
9 |
| 785 |
2004 |
C/16/04 |
Process Management and Material Flow Control in High Pressure Sheet Metal Forming |
M. Trompeter, W. Homberg, M. Kleiner |
6 |
| 786 |
2004 |
C/17/04 |
Locally Heat Treated Blanks - An Approach to improve the Process in Sheet Metal Forming |
M. Hogg, K. Roll |
10 |
| 787 |
2004 |
C/18/04 |
Manufacturing a Roof Frame from Ultra High Strength Steel Materials by Hot Stamping |
G. SchieBl, Th. Possehn, Th. Heller, S. Sikora |
9 |
| 788 |
2004 |
C/19/04 |
Manufacturing Methods for Safety and Structure Body Parts for Lightweight Body Design |
R. Kolleck, J.-A. Feindt, F.-J. Lenze, Th. Heller |
7 |
| 789 |
2004 |
C/20/04 |
State of the Art regarding Design, Modeling and Processing of Spot-welded Patched Blanks for the Automotive Industry |
F. Pinard, L. Cretteur |
8 |
| 790 |
2004 |
C/21/04 |
The Influence of Lubricants and Tooling on Galling and Tool Wear of Galvanized Steel |
Ch. Dane, E. van der Heide |
10 |
| 791 |
2004 |
C/22/04 |
Damaging Mechanisms of Coatings on Steel Sheet during Forming |
C. Ostwald, G. Grundmeier, A. Simoes |
6 |
| 792 |
2004 |
C/23/04 |
Representation of Forming Limits for Negative Incremental Forming of Thin Sheet Metals |
L. Carrino, M. Ruggiero, M. Strano |
10 |
| 793 |
2004 |
C/24/04 |
Finite Element Analysis of Multi-Stage Deep-Drawing Processes with Intermediate Heat Treatments |
R. Rowshan, M. Tisza |
8 |
| 794 |
2004 |
C/25/04 |
Guideline for the Determination of Forming Limit Curves |
H. Liebertz, S. Keller, M. Merklein, R. Illig, A. Koehler, A. Kroff,J. Rauer, L. Staubwasser, G. Steinbeck. W. Holz, H. Vegter, A. Duwel |
9 |
| 795 |
2004 |
C/26/04 |
Numerical and experimental Study of the Influence of Sheet Thickness on Forming Limits |
L P. Moreira, G. Ferron, M. Martiny, A. P. Sampaio, A. C. L de Oliveira |
10 |
| 796 |
2004 |
C/27/04 |
Influence of Scatter of Material Properties on the Formability of Parts |
F. Rechberger, E. T. Till |
10 |
| 797 |
2004 |
C/28/04 |
Innuence of Bake Hardening Treatment and Strain Ageing Time on Dent Resistance of Different Automotive Steel Grades |
St. Pellissetti, E. Berger, E. Till |
16 |
| 798 |
2004 |
C/29/04 |
Deformation and Mechanical Properties of High Manganese TRIP Alloys |
R. Visorova, J. Kroos, V.Flaxa, J. Wendelstorf: K.-H. Spitzer |
10 |
| 799 |
2004 |
C/30/04 |
Properties of Light Steels with Induced Plasticity (L-IP Steels) |
H. Hofmann |
10 |
| 800 |
2004 |
C/31/04 |
Formability of Sandwich Sheets for Automobile Parts |
R. Kapp, M. Nutzmann |
11 |
| 801 |
2004 |
C/32/04 |
Dynamic Forming of Sheet Materials for Parts Protoypes |
V. Vovk, V. Taran, A. Vovk |
7 |
| 802 |
2004 |
C/33/04 |
Exactness Visualization of Press Parts and Tools by the Optical Digitizing System A TOS |
K. Galanulis, C. Reich, J. Thesing, D. Winter |
9 |
| 803 |
2004 |
C/34/04 |
Springback Evaluation Applying the Splitting Ring Benchmark Test in Tailored Welded Blanks |
J. L. Alves, A. J. Baptista, M. C. Oliveira, D. M. Rodrigues, L F. Menezes |
11 |
| 804 |
2004 |
C/35/04 |
Finite Element Simulation of Deep Drawing with Initial and Induced Anisotropy |
B. Haddag, T. Balan, F. Abed-Meraim |
7 |
| 805 |
2004 |
C/36/04 |
Numerically based Compensation of Springback Deviations During Die Process Engineering of Complex Car Parts |
T. Lemke, M. Rohleder, K. Roll, K. Wiegand |
9 |
| 806 |
2004 |
C/37/04 |
Simulation of Hydroforming Processes using a New Orthotropic Yield Criterion |
G. Cosovici, D. S. Comsa, D. Banabic, S. Wagner, K. Siegert |
10 |
| 807 |
2004 |
C/38/04 |
Hot Stamping Drawability of Steel Sheet |
T. Asai, J. Twaya |
11 |
| 808 |
2004 |
C/39/04 |
Draw Bending, an Alternative for the Production of Load Adapted Profiles |
E. Doege, B.-A. Behrens, S. Mutze, V. Ulbricht, D. SuBe |
12 |
| 809 |
2004 |
C/40/04 |
Analytical Models for the Evaluation of Tube Bendability |
F. Campana, E. Amici, F. Ballerini, E. Mancini, M. Tavassi |
7 |
| 810 |
2004 |
C/41/04 |
Thin Sheet Metal Hydroforming |
A. Wellendorf, W. Homberg, M. Kleiner |
5 |
| 811 |
2004 |
C/42/04 |
Development of New Press Forming Technique for Laser Welding of Overlapped Zinc Coated Steel Sheets |
M. Nakata, Y. Kirose, K. Fukui, H. Fujimoto |
10 |
| 812 |
2004 |
C/43/04 |
Texture Development during Mechanical r- Value Determination |
J. Gerlach, H. Klein, Ch. Klinkenberg |
8 |
| 813 |
2004 |
C/44/04 |
Application of Load Adjusted Flow Curves in the FE-Simulation and Verification with Experimental ResuIts |
E. Doege, B.-A. Behrens, B. Springub, C. Sunderkotter |
10 |
| 814 |
2005 |
C/1/05 |
Some considerations on experimental and numerical aspects linked to deep-drawing: examples of interest and limitations |
F. Moussy |
29 |
| 815 |
2005 |
C/2/05 |
Local strain prediction in small die radii regions – Optimization of numerical simulation parameters for modelling a part door outer |
E. Berger, T. Brenne, A. Heath, B. Hochcoldinger, K. Kassem-Manthey, L. Kessler, N. Koch, G. Kortmann, A. Kröff, T. Otto, G. Steinbeck, E. Till, H. Verhoeven, T.C. Vu, K. Wiegand |
8 |
| 816 |
2005 |
C/3/05 |
Development of a reliable and economic Forming Process for Magnesium Sheet Metal |
B. A. Berhens, O. Vogt, J. Poelmeyer |
7 |
| 817 |
2005 |
C/4/05 |
Experimental Study of Springback Elimination Using Electromagnetic Forming |
E. Iriondio, B. Gonzalez, I. Eguia, M. Gutierrez, G. S. Daehn |
7 |
| 818 |
2005 |
C/5/05 |
Trimming of aluminium alloys sheets: experimental and numerical investigations |
A. Bacha, H. Klocker, D. Daniel |
10 |
| 819 |
2005 |
C/6/05 |
The development of aluminium alloy sheets with high formability for automotive applications |
H. Hayashi, H. Tanaka, T. Komatsubara, K. Koyama, H. Nishimura |
9 |
| 820 |
2005 |
C/7/05 |
Challenges for high volume aluminium car body applications |
D. Daniel, P. Litalien, R. Shahani |
12 |
| 821 |
2005 |
C/8/05 |
Direct identification of a combined hardening with a cyclic bending test |
P. Simon, F. Sabourin, F. Morestin, L. Phan |
10 |
| 822 |
2005 |
C/9/05 |
How well do virtual stampings compare to real parts? |
M. Roelofsen, C. ten Horn |
10 |
| 823 |
2005 |
C/10/05 |
3D Finite Element Modeling and Analysis of the Laminated Tooling Behaviour in Sheet Metal Stamping Process |
M. Oudjene, F. Mercier, L. Penazzi, J.L. Batoz |
9 |
| 824 |
2005 |
C/11/05 |
Statistical modelling of geometrical constraints for high-pressure sheet metal hydroforming |
M. Gösling, W. Homberg, M. Kleiner, Ch. Klimmek |
11 |
| 825 |
2005 |
C/12/05 |
Press hardening of boron steel sheets – forming and tooling technology with high potential |
R. Kolleck, S. Pfanner, H. Kasseger, C. Lind |
10 |
| 826 |
2005 |
C/13/05 |
Effective stamping simulation using automatic blank and process optimization techniques |
A. Chambard, P. Guyon, F. El Khaldi, M. Lambriks, D. Ling |
8 |
| 827 |
2005 |
C/14/05 |
Expert tools for stamping |
C. Bouhêlier, P. Marchand, H. Sfar |
9 |
| 828 |
2005 |
C/15/05 |
Simulation of deep-drawing of TRIP-assisted multiphase steel based on a micro-macro modelling |
L. Delannay, F. Lani, P.J. Jacques |
10 |
| 829 |
2005 |
C/16/05 |
Implementation of a non-isothermal material model for austenitic stainless steels in deep drawing simulation - Finding of optimum process parameters for improving deep drawability |
J.L. Avendano, J. I. Fernandez, E. Schedin, J. Kajberg, E. Ratte, A. Frehn |
9 |
| 830 |
2005 |
C/17/05 |
Predictive model of FLC (Arcelor model) upgraded to UHSS steels |
F. Cayssials, X. Lemoine |
8 |
| 831 |
2005 |
C/18/05 |
On the choice of yield criterion for industrial sheet forming simulations |
K. Mattiasson, M. Sigvant |
10 |
| 832 |
2005 |
C/19/05 |
Testing a combined isotropic and non-linear kinematic hardening model in forming of austenitic stainless steel |
A. Revuelta, T. Manninen, J. Larkiola, A.S. Korhonen |
8 |
| 833 |
2005 |
C/20/05 |
Concepts for characterizing plastic anisotropy of sheet metal |
K. Pöhlandt, A.E. Tekkaya, J. Schöck |
16 |
| 834 |
2005 |
C/21/05 |
Estimation of stamping forces for High Strength Steels |
G. Mercuzot, P. Hein |
10 |
| 835 |
2005 |
C/22/05 |
A New Method to Evaluate and Compensate Springback |
T. Kondou, G. Uemura, K. Ito, N. Mori |
8 |
| 836 |
2005 |
C/23/05 |
Process control strategies for high-pressure sheet metal forming of large-scale structure parts |
M. Trompeter, R. Krux, W. Homberg, M. Kleiner |
8 |
| 837 |
2005 |
C/24/05 |
Virtual pre-matching |
B. Axelsson, A. Andersson |
10 |
| 838 |
2005 |
C/25/05 |
FLCs: are we at a turn? |
A. Col |
10 |
| 839 |
2005 |
C/26/05 |
A user-friendly programme for analyzing the anisotropy and formability of sheet metals |
P. Jurco, D. Banabic |
9 |
| 840 |
2005 |
C/27/05 |
Development of a modular Forming Limit Diagram code and its application to F.E. simulation |
P. Teixeira, M.C. Butuc, A.D. Santos, A.Barata da Rocha, J.J. Gracio |
10 |
| 841 |
2005 |
C/28/05 |
The influence of temperature on the formability of metal/polymer/metal-laminates |
M. Weiss, M. Dingle, B.F. Rolfe, P.D. Hodgson |
9 |
| 842 |
2005 |
C/29/05 |
Numerical determination of specific forming limit curve for tailor welded-blanks using the major strain rate criterion |
S. Gaied, F. Pinard, F. Schmit, J.M. Roelandt |
8 |
| 843 |
2005 |
C/30/05 |
Investigation of the springback behavior in metal foil forming |
A. Diehl, U. Engel, M. Geiger |
10 |
| 844 |
2005 |
C/31/05 |
Manufacturing complex sheet metal components by hydrofroming of deep-drawn preforms |
K. Lamprecht, M. Merklein, M.Geiger |
9 |
| 845 |
2005 |
C/32/05 |
Study on the thinning during single point incremental forming of aluminium sheets |
A. Van Bael, S. He, P. Van Houtte, Y. Tunckol, J. Verbert, J. Duflou |
12 |
| 846 |
2005 |
C/33/05 |
Numerical study of the effects of processing parameters in the high-speed blanking in the connectic field |
Ch. Husson, S. Ahzi, L. Daridon, C. Poizat |
10 |
| 847 |
2005 |
C/34/05 |
New approach to demonstrate the need for a dedicated friction model to improve numerical simulations |
C. Dane, H. Vegter, M. Workel, R. Boulanger |
10 |
| 848 |
2005 |
C/35/05 |
Global analysis method of friction parameters in strip drawing tests |
J.M. Pothier, X. Roizard, J.Y. Hihn, J.F. Beteau, G. Monteil |
11 |
| 849 |
2005 |
C/36/05 |
Influence of lubricants and tool materials upon galling of stainless steels |
G. Lovato, H. Giraud, E. Van Der Heide, E.D. Stam, I. Heikkila, N. Akdut, F. Clarysse, P. Caenen |
10 |
| 850 |
2005 |
C/37/05 |
A study of roughness anisotropy of surfaces produced by laboratory and industrial rolling and surfaces generated by computer modelling |
C.M. Wichern, W. Rasp |
8 |
| 851 |
2005 |
C/38/05 |
Modeling effects in springback simulation |
E. Till, A. Raab |
11 |
| 852 |
2005 |
C/39/05 |
Numerical and experimental study on the splitting ring test for springback prediction |
A.J. Baptista, B.M. Chaparro, J.M. Antunes, D.M. Rodrigues, L.F. Menezes |
9 |
| 853 |
2005 |
C/40/05 |
Forming techniques and forming analysis on spring-back for high strength steel in sheet metal forming |
E. Isogai, T. Yoshida, N. Suzuki, A. Uenishi, Y. Kuruyama |
8 |
| 854 |
2005 |
C/41/05 |
A method of springback and tool compensation based on finite element method and design of experiment |
Y. Ledoux, E. Pairel, R. Arrieux, P. Teixeira, A.D. Santos, J. Duarte |
10 |
| 855 |
2005 |
C/42/05 |
Validation of springback, influence and sensitivity on a real world automotive part |
B. Carleer, T. Zwickl, L. Schidzig, A. Wendenburg |
10 |
| 856 |
2005 |
P/43/05 |
A new equation to describe the effect of microstructural transformation of austenitic stainless steels during plastic deformation |
R. Andersson, M. Oden, J. Powell, C. Magnusson |
1 |
| 857 |
2005 |
P/44/05 |
Optimisation of process parameters for the minimisation of stressfield and bending load in sheet metal bending operation |
R. Bahloul, Ph. Dal Santo |
10 |
| 858 |
2005 |
P/45/05 |
Innovative testing methods for tinplate |
W. Bleck, B. Kaup, G. Pariser, E. Ratte, R. Sauer, C. Thomser |
5 |
| 859 |
2005 |
P/46/05 |
Effect of wrinkling on delayed fracture in deep drawing |
B. Carlsson |
5 |
| 860 |
2005 |
P/47/05 |
Influence of the specimen geometry for the determination of the Uniaxial Tension necking point for FLD |
J-L. Geoffroy, J-P. Adami |
2 |
| 861 |
2005 |
P/48/05 |
Electromagnetic forming for automotive applications in LABEIN |
B. Gonzales, I. Eguia, M. A. Guttierez, J. L. Fernadez, A. Arroyo, E. Iriondo, P. Jimbert |
9 |
| 862 |
2005 |
P/49/05 |
Springback Characterization and Control of Advanced High Strength Steel |
M. Huang |
1 |
| 863 |
2005 |
P/50/05 |
Hemming simulation with different element formulations and material models |
C. Lange, E. Felder, E. Massoni, P. Auger, A. Kanji Nanji |
10 |
| 864 |
2005 |
P/51/05 |
Implentation of advanced behaviour laws and validation in numerical prediction for sheet metal forming |
G. Racz, X. Lemoine, T. Balan |
10 |
| 865 |
2005 |
P/52/05 |
Experimental and numerical analysis of the formability of TRIP steels |
N. Bourgeois, R. Makkouk, J. Serri, M. Martiny, G. Ferron |
9 |
| 866 |
2005 |
P/53/05 |
New complex evaluation of formability |
H. Stroppe, V. Vovk, A. Vovk, V. Taran |
5 |
| 867 |
2005 |
P/54/05 |
Calculation of Strain After Bending over a Roller with a Known Restraining Force |
C. J. Van Tyne, B. S. Levy, Y. H. Moon |
7 |
| 868 |
2005 |
P/55/05 |
Forming methods increasing the strength of austenitic stainless steel products |
B. Wadman, R. Moshfegh, H. Groth, H. Roos, P. A. Carlsson, J. Bernquist, A. Alrutz |
11 |
| 869 |
2005 |
P/56/05 |
Study of the strain rate effect on SPCC and Al6XXX with numerical simulation |
L. Wang, T. C. Lee, L. C. Chan |
1 |
| 870 |
2006 |
C/1/06 |
Methods for forming limit prediction in ductile metal sheets |
K. Mattiasson, M. Sigvant, M. Larsson |
10 |
| 871 |
2006 |
C/2/06 |
A note on forming limits and forming limit stress diagrams |
E. T. Till, C. Walch, H. Pauli |
8 |
| 872 |
2006 |
C/3/06 |
Issues on the AHSS forming limit determination |
M. F. Shi, S. Gelisse |
8 |
| 873 |
2006 |
C/4/06 |
Hydroforming of DP600 straight tubes with load control end-feed - experiment and modelling |
A. Bardelcik, M.J. Worswick |
8 |
| 874 |
2006 |
C/5/06 |
Forming limit prediction by finite element simulation combined with ductile fracture criterion - Application to three dimensional press forming processes of high-strength steel sheets |
H. Takuda, T. Maruyama, E. Isogai, T. Yoshida |
8 |
| 875 |
2006 |
C/6/06 |
Damage prediction in sheet metal forming: theory, numerics and application |
K. Saanouni, H. Badreddine |
8 |
| 876 |
2006 |
C/7/06 |
Forming limit prediction using BBC 2003 yield criterion for aluminum automotive alloy |
M. Vos, D. Banabic, P. Jurco, J. Brem, F. Barlat |
8 |
| 877 |
2006 |
C/8/06 |
Formability evaluation in warm conditions of AZ31 magnesium alloy |
G. Palumbo, D. Sorgente, L. Tricarico, S.H. Zhang, W.T. Zheng, L. X. Zhou |
6 |
| 878 |
2006 |
C/9/06 |
Forming limits of DP600 TWBs during biaxial stretching |
R. Davies, F. Stavehaug, G. Grant, E. Stephens |
8 |
| 879 |
2006 |
C/10/06 |
Semi-analytical identification of the flow curve extrapolation in consideration of martensite evolution |
B. Springub, B.-A. Behrens |
8 |
| 880 |
2006 |
C/11/06 |
Modified maximum force criterion for prediction of FLC and for optimization of blankholder forces in stamping |
L. Ben Ayed, A. Delamézière, J.-L. Batoz, C. Knopf-Lenoir |
8 |
| 881 |
2006 |
C/12/06 |
A study on the improvement of forming limit prediction accuracy in sheet metal forming simulation - gauge length dependency of fracture limit strain |
J. Nitta, T. Yoshida, K. Hashimoto, Y. Kuriyama |
8 |
| 882 |
2006 |
C/13/06 |
Testing material formability in hot stamping operations |
A. Turetta, A. Ghiotti, S. Bruschi |
6 |
| 883 |
2006 |
C/14/06 |
Characterization of yielding and hardening of AA6016 |
W. Hußnätter, M. Merklein |
8 |
| 884 |
2006 |
C/15/06 |
The impact of material testing strategies on the determination and calibration of different FEM material models |
L. Kessler, J. Gerlach |
7 |
| 885 |
2006 |
C/16/06 |
Long and short term strategy to deal with material property variation in sheet-metal forming |
E. H. Atzema, H. Brouwer, P. Kömmelt |
8 |
| 886 |
2006 |
C/17/06 |
A new method for wrinkling prediction of steel complex-shaped packaging |
O. Beigneux, J. J. Li, L. Dreystadt, R. Cappelletti, S. Tref, A. Leplomb |
8 |
| 887 |
2006 |
C/18/06 |
Plastic behavior upon reverse loading of steel sheet and its application to dimensional control of stampings |
B.S. Levy, C.J. Van Tyne |
8 |
| 888 |
2006 |
C/19/06 |
A model of large-strain cyclic plasticity for accurate springback analysis |
F. Yoshida, T. Uemori, S. Abe |
8 |
| 889 |
2006 |
C/20/06 |
Finite element analysis of high strength steel stamping process adopting a combined kinematic-isotropic hardening model: experimental investigation on the improvements achieved in springback prevision |
F. Campana, L. Cortese, F. Placidi |
8 |
| 890 |
2006 |
C/21/06 |
Numerical evaluation of the influence of the elastic properties evolution in springback prediction |
J. L. Alves, M. C. Oliveira, L.F. Menezes |
8 |
| 891 |
2006 |
C/22/06 |
3D FEM simulation of sheet metal hydrostatic bulging for IF steel sheet metal forming |
J. P. Abrantes, R. L. L. P. Cerveira, G. F. Batalha |
8 |
| 892 |
2006 |
C/23/06 |
Constitutive modelling of sheet metals in the finite strain regime |
I. N. Vladimirov, S. Reese |
6 |
| 893 |
2006 |
C/24/06 |
Determination of metal sheet formability using a new technological proofing method |
R. Hennig, S. E. S. Netto, L. Schaeffer |
8 |
| 894 |
2006 |
C/25/06 |
Basic investigations into wrinkling limits for Incremental sheet forming |
G. Ambrogio, M. Bambach, L. Filice, G. Hirt |
8 |
| 895 |
2006 |
C/26/06 |
The influence of temperature on the springback behavior of metal/polymer-laminates |
M. Weiss, B.F. Rolfe, P.D. Hodgson |
8 |
| 896 |
2006 |
C/27/06 |
Mechanical characterization of automotive aluminium alloys |
B.M. Chaparro, D.M. Rodrigues, S. Thuillier, J.V. Fernandes, L.F. Menezes |
8 |
| 897 |
2006 |
C/28/06 |
Study of the inelastic response of trip steels after plastic deformation |
R. Pérez, J. A. Benito, J. M. Prado |
8 |
| 898 |
2006 |
C/29/06 |
A new experimental method to evaluate sheet bending forces under multiaxial stresses conditions |
V. Miguel, A. Calatayud, A. Martínez, J. Coello, C. Ferrer |
8 |
| 899 |
2006 |
C/30/06 |
New rotational kinematics in anisotropic elasto–plasticity with damage |
H. Badreddine, K. Saanouni, A. Dogui |
8 |
| 900 |
2006 |
C/31/06 |
Finite element prediction of fracture onset in sheet metal forming using a ductile damage model |
P. Teixeira, F.M. Andrade Pires, A.D. Santos, J. César de Sá |
8 |
| 901 |
2006 |
C/32/06 |
Crystallographic texture changes on zinc coated steel sheets during deformation |
V. Vaché, M. Knoll, R. Logé, M. Repoux, J.M. Mataigne |
8 |
| 902 |
2006 |
C/33/06 |
An investigation to the effects of cold work and heat treatment processes (warm work) on the eutectic morphology in ALTHIX (A356) alloy |
M. Haghshenas, A. Zarei-Hanzaki |
4 |
| 903 |
2006 |
C/34/06 |
Experimental and numerical simulation of the austenite - ferrite phase transformation |
G. Pariser, U. Prahl, W. Bleck |
7 |
| 904 |
2006 |
C/35/06 |
Constitutive modeling for plastic anisotropy and application to convolute cut-edge design |
J.W. Yoon, F. Barlat, R.E. Dick |
4 |
| 905 |
2006 |
C/36/06 |
Different approaches to model the material separation during blanking process using FEM |
B.-A. Behrens, K. Bir Sidhu, O. Pösse |
8 |
| 906 |
2006 |
C/37/06 |
Two stage forming: experimental and FE analysis |
M.C. Oliveira, A.J. Baptista, J.L. Alves, L.F. Menezes, D.E. Green, T. Gnaeupel-Herold, M.A. Iadicola, T. Foecke, T.B. Stoughton |
6 |
| 907 |
2006 |
C/38/06 |
Numerical simulation of flat-surface roll hemming: influence of geometry and material models |
N. Le Maoût, S. Thuillier, P.Y. Manach, D. Debois, J.C. Wadoux |
8 |
| 908 |
2006 |
C/39/06 |
Hot-forming-process important parameters for the production of high-strength BIW parts |
S. Sikora, F.-J. Lenze |
8 |
| 909 |
2006 |
C/40/06 |
Development of one step crimping solutions for car industry |
F. Boór |
8 |
| 910 |
2006 |
C/41/06 |
Experimental identification and numerical verification of the process window in the warm forming of magnesium sheet metal (AZ31) |
M. Redecker, K. Roll, S. Hong, H. Hoffmann |
8 |
| 911 |
2006 |
C42/06 |
Hydromechanical deep drawing of complicated thin walled components with magnesium alloy AZ31 sheets |
S. H. Zhang, L. M. Ren, L. X. Zhou, Y. C. Xu, A. Y. Yuan, L. Q. Ruan |
6 |
| 912 |
2006 |
C/43/06 |
Tooling design for warm hydroforming based on temperature pattern analysis |
A. Aginagalde, J. A. Esnaola, C. García, I. Perez, M. Gutierrez |
8 |
| 913 |
2006 |
C/44/06 |
Service life optimization in the context of cutting high-strength and highest-strength sheet steels |
R. Kolleck, J. Danzinger, W. Haidenthaler, M. Kalcher, S. Raschka, C. Lind, J. Winklhofer |
8 |
| 914 |
2006 |
C/45/06 |
Basic investigation into the characteristics of dies and support tools used in CNC-incremental sheet forming |
G. Hirt, J. Ames, M. Bambach |
8 |
| 915 |
2006 |
C/46/06 |
Thermal-mechanical coupled simulation on the forming of hot press formed part |
H.G. Kim, H.S. Son, S.Y. Kang, S.H. Park |
8 |
| 916 |
2006 |
C/47/06 |
Deep drawing behaviour and mechanical properties of tailored hybrid blanks |
M. Kreimeyer, F. Vollertsen |
8 |
| 917 |
2006 |
C/48/06 |
Numerical simulation of thinning processes |
B.-A. Behrens, O. Poesse, K. Bir Sidhu, J. Poelmeyer |
6 |
| 918 |
2006 |
C/49/06 |
A gradient based approach for the design of the shape of the blank in deep drawing of rectangular boxes |
R. Di Lorenzo, G. Ingarao, F. Micari |
|
| 919 |
2006 |
C/50/06 |
One point quadrature solid-shell elements for sheet metal forming applications |
R. P. R. Cardoso, J.-W. Yoon, R. J. A. de Sousa, R. A. F. Valente, J. J. Grácio |
8 |
| 920 |
2006 |
C/51/06 |
A numerical simulation approach to the aerosols and food cans manufacture and decoration |
L. Neamtu, F. Flores, R. Weyler, E. Oñate |
8 |
| 921 |
2006 |
C/52/06 |
Formability investigations for the hot stamping process |
Y. Dahan, Y. Chastel, P. Duroux, P. Hein, E. Massoni, J. Wilsius |
8 |
| 922 |
2006 |
C/53/06 |
Technology of improving press formability applying press motion control - advanced multi-stage forming with servo press - |
Y. Tamai, Y. Yamasaki, A. Yoshitake, T. Imura |
6 |
| 923 |
2006 |
C/54/06 |
Multiple step drawing of high strength HSLA-, dual phase- and martensitic steel sheet |
M. Fallqvist, B. Carlsson |
6 |
| 924 |
2006 |
C/55/06 |
On the influence of high speed forming technologies in the forming of conical specimens: fluid-specimen interaction against magnetically induced repulsion |
P. Jimbert, I. Eguia, E. Iriondo J. I. Fernandez, E. Silveira, I. Garuz |
6 |
| 925 |
2006 |
C/56/06 |
Tailor rolled blanks - experimental and numerical analysis of the deep drawing behaviour |
G. Hirt, A. Meyer |
8 |
| 926 |
2006 |
C/57/06 |
Formability assessment of laser welded blanks by numerical and analytical approaches |
S. Gaied, F. Pinard, F. Schmit, J.-M. Roelandt |
8 |
| 927 |
2006 |
C/58/06 |
Downgauging and optimisation of the base profile of beverage cans for nose growth and dome reversal |
G. T. Nagy, H. Mulder, D. Vercammen |
8 |
| 928 |
2006 |
C/59/06 |
Numerical simulation of sheet metal blanking, predicting the material state near the cut edge |
A. Ben Ismail, H. Marouani, M. Rachik, E. Hug, M. Fafard |
8 |
| 929 |
2006 |
C/60/06 |
Blank shape optimisation using parametric NURBS surfaces |
R. Padmanabhan, A.J. Baptista, M.C. Oliveira, M. Tekaya, A. Dogui, B. H. Salah, J. L. Alves, L.F. Menezes |
8 |
| 930 |
2006 |
C/61/06 |
Modeling of hydromechanical deep drawing process using numerical method |
M. Zohoor, M. Sima |
6 |
| 931 |
2006 |
C/62/06 |
Hydroforming of partially cladded double blanks |
M. Kleiner, M. Trompeter, M. Gösling, W. Homberg, H. Karbasian, B. Rauscher |
8 |
| 932 |
2006 |
C/63/06 |
Hydroforming of tailor-welded tubular blanks: simulation using EAS solid-shell finite elements |
A.P. Roque, R.A.F. Valente, M.P.L. Parente, R.M. Natal Jorge, A.A. Fernandes |
6 |
| 933 |
2006 |
C/64/06 |
and prediction of yield stress change for UOE pipes by finite element analysis |
K.-C. Park |
8 |
| 934 |
2006 |
C/65/06 |
Research in the process of deep drawing of sheet molybdenum containers for growing single crystals |
E.A. Nazaryana, M. M. Arakelyanb |
6 |
| 935 |
2006 |
C/66/06 |
A case study of web-based expert system for sheet metal forming operations |
R. S. Hingole, V. M. Nandedkar |
8 |
| 936 |
2006 |
C/67/06 |
Comparison of two optimization methods of forming operation for the springback compensation based on numerical simulations |
Y. Ledoux, E. Pairel, R. Arrieux |
8 |
| 937 |
2006 |
C/68/06 |
Optimization system based on Lmeca - Taguchi’s/neural network methods for the compensation of errors generated by springback in the case of draw parts made from metal sheets |
G. Brabie, F. Ene, C. Axinte |
6 |
| 938 |
2006 |
C/69/06 |
Improvement of springback FEM simulation by means of an optimization procedure based on an experimental trial |
A. Mangas, A. Arroyo, I. Fernandez, B. Gonzalez |
6 |
| 939 |
2006 |
C/70/06 |
Shear deformation properties of ultra high strength steel sheet |
M. Nakata, K. Uematsu, S. Koseki |
8 |
| 940 |
2006 |
C/71/06 |
Parametric die compensation |
R. Bernard, H. Bühling, M. Heinrich, V. Huthmacher, G. Jung, S. Kulp, S. Richter, P Salzmann, R. Struck, M. Taeschner, H. Verhoeven, P. Weigert |
8 |
| 941 |
2006 |
C/72/06 |
Quantitative analysis of robustness in a simulated stamping process |
T. de Souza, B. Rolfe, J.L. Duncan, P.D. Hodgson |
8 |
| 942 |
2006 |
C/73/06 |
Influence on simulation results from material and process scatter |
M. Sigvant, B. Carleer |
6 |
| 943 |
2006 |
C/74/06 |
Influence of drawbeads in deep drawing of plane-strain channel sections |
D. E. Green, T. B. Stoughton, T. Gnaeupel-Herold, M. A. Iadicola, T. Foecke |
6 |
| 944 |
2006 |
C/75/06 |
Springback and twist prediction of roll formed parts |
Q. V. BUI, R. Boman, L. Papeleux, P. Wouters, R. Kergen, G. Daolio, P. Duroux, P. Flores, A.M. Habraken, J.P. Ponthot |
8 |
| 945 |
2006 |
C/76/06 |
Numerical study of wrinkling and springback in electromagnetic sheet metal forming |
J.P.M. Correia, M.A. Siddiqui, S. Ahzi, M.A. Khaleel |
6 |
| 946 |
2006 |
C/77/06 |
High speed laser cutting of metallic thin sheets |
T. B. Faro, R. M. Miranda, A. A. Fernandes |
8 |
| 947 |
2006 |
C/78/06 |
A simplified procedure for the design of multi-layered forming tools assembled by screws |
M. Oudjene, J-L. Batoz, L. Penazzi, A. Delamézière, F. Mercier |
8 |
| 948 |
2006 |
C/79/06 |
Die materials, hardening methods and surface coatings for forming of high, extra high & ultra high strength steel sheets (HSS/EHSS/UHSS) |
M. Liljengren, K. Kjellsson, T. Johansson, N. Asnafi |
8 |
| 949 |
2006 |
C/80/06 |
Virtual and real prototyping of sheet metal components |
R. M. O. S. Baptista, M. B. Silva, C. Saraiva |
8 |
| 950 |
2006 |
C/81/06 |
On laser hardening of trimming tools & dies |
A. Ullman, K. Kjellsson, T. Johansson, N. Asnafi |
8 |
| 951 |
2006 |
C/82/06 |
Improvement of performance of cold forming tools through microstructural tailoring |
D. Casellas, J. Caro, S. Molas, A. Beltran, J.M. Prado |
6 |
| 952 |
2006 |
C/83/06 |
Galling in sheet metal forming of aluminum: a numerical approach |
E. R.M. Gelinck, E. van der Heidea, M. B. de Rooijb, D. J. Schipperb |
8 |
| 953 |
2006 |
C/84/06 |
Enhancing the wear simulation of sheet metal forming processes with variable wear coefficients |
K. Ersoy, G. Herrmann, G. Nuernberg, M.Golle |
8 |
| 954 |
2006 |
C/85/06 |
Corrosion protection primer - processing in the press shop |
A. Adleff, F. Androsch, A. Besseyrias, C. Dane, U. Eggers, C Guillon, M. Hoerning, A. Pscheidt, G. Steinbeck, S. Woestmann |
8 |
| 955 |
2006 |
C/86/06 |
Frictional properties of different austenitic stainless steel sheet surface topographies: industrial trials at Alfa Laval |
A. Bellini, P. Gabrielson, D. Wiklund, L. Gunnarsson |
8 |
| 956 |
2006 |
C/87/06 |
Correlation of surface topography and friction coefficients for low carbon steel subjected to flat die drawing |
W. Rasp, C. M. Wichern, J. Valentin |
8 |
| 957 |
2006 |
C/88/06 |
Influence of virgin automotive sheet steel surface texture on paint appearance and forming properties |
B.-G. Rosén, E. Roos, D. Wiklund |
6 |
| 958 |
2006 |
C/89/06 |
Topographical analysis of aluminum surfaces with textured finishes using confocal white light microscopy |
C. M. Wichern, J. Valentin, J. M. Epp, D. E. Coleman |
6 |
| 959 |
2007 |
C/1/07 |
Robust Processes in Sheet Metal Forming in Car Body Manufacturing with Regard to Production Volume |
M. Liewald, R. Schleich |
10 |
| 960 |
2007 |
C/2/07 |
Numerical and Experimental Evaluation of Thermal Dependent FLC (FLC-T) |
P. Hora, M. Merklein, L. Tong, J. Lechler |
8 |
| 961 |
2007 |
C/3/07 |
Toolmaking for Future Car Bodies: Toolmaking as Pioneer for Quality, Speed and Cost Reduction for the Development and Production of New Car Body Concepts |
H. Waltl, W. Vette, Dr. B. Griesbach |
13 |
| 962 |
2007 |
C/4/07 |
Strain Hardening Behavior of Modern Light-Weight Car Body Sheet Steels |
A. Bäumer, W. Bleck |
8 |
| 963 |
2007 |
C/5/07 |
Numerical Simulation of Deep Drawing of Dual-Phase Steel |
P. Kostka, P. Žitňanský, P. Čekan, A. Schrek |
5 |
| 964 |
2007 |
C/6/07 |
Simulation Capability of Advanced High Strength Steels |
E. T. Till, M. Flahaut, C. Walch |
9 |
| 965 |
2007 |
C/7/07 |
Bending Test and Bendability of Ultra High Strength Steels |
I. Boul, M. Lang, G. Mees, F. Sponem, T. Sturel, X. Garat |
8 |
| 966 |
2007 |
C/8/07 |
Numerical Simulation of Microstructure Evolution during the Hot Stamping Process |
B.-A. Behrens, P. Olle, F. Schäfer, C. Schäffner |
8 |
| 967 |
2007 |
C/9/07 |
Modelling the Mechanical Properties of Multiphase Steels Based on Microstructure |
C. Thomser, H. Vegter, U. Prahl, W. Bleck |
6 |
| 968 |
2007 |
C/10/07 |
Non-Destructive Testing for the Determination of Transformation Induced Martensite in Metastable Austenitic Steels |
B.-A. Behrens, K. Voges-Schwieger, S. Huebner |
8 |
| 969 |
2007 |
C/11/07 |
A Contribution on Yield Loci Modeling Compared to the Application of Variable Hardening Curves in Forming Simulations |
L. Kessler, H. Richter, K. Roll, A. Faust |
7 |
| 970 |
2007 |
C/12/07 |
Evaluation of Material Models and Element Types for Sheet Metal Forming of Titanium |
P. Gabrielson, L. Ekdahl, R. Moshfegh |
8 |
| 971 |
2007 |
C/13/07 |
Impact of a Non Associative Plasticity on Damage Prediction in Sheet Metal Forming |
H. Badreddine, K. Saanouni, A. Dogui |
8 |
| 972 |
2007 |
C/14/07 |
Procedure for the Experimental Determination of a Forming Limit Curve for Usibor 1500 P |
Y. Dahan, Y. Chastel, P. Duroux, J. Wilsius, P. Hein, E. Massoni |
8 |
| 973 |
2007 |
C/15/07 |
Tube Bulge Process : Theoretical Analysis and Finite Elements Simulations |
R. Velasco, N. Boudeau |
6 |
| 974 |
2007 |
C/16/07 |
Study of the Frictional Behavior of Austenitic Stainless Steel Sheet Under Flat-Die Friction Testing |
J. Coello, V. Miguel, C. Ferrer, A. Calatayud, A. Martínez |
8 |
| 975 |
2007 |
C/17/07 |
Investigation of 22MnB5 Mechanical and Phase Transformation Behaviour at High Temperature |
A. Turetta, A. Ghiotti and S. Bruschi |
7 |
| 976 |
2007 |
C/18/07 |
A Critical Assessment of Various Failure Criteria for Predicting Forming Limit Strains during Stamping |
N. S. Dhanajkar, M. M. Ghadmode, K. Narasimhan |
8 |
| 977 |
2007 |
C/19/07 |
The Forming Limit Band - A New Tool for Increasing the Robustness in the Simulation of Sheet Metal Forming Processes |
M. Vos, D. Banabic |
12 |
| 978 |
2007 |
C/20/07 |
Adequately Use FLC’s for Simulation |
J-L. Geoffroy, J. Goncalves, X. Lemoine |
8 |
| 979 |
2007 |
C/21/07 |
Theoretical and Experimental Sheet Metal Failure Evaluation |
K. Mattiasson, M. Sigvant, M. Larsson |
10 |
| 980 |
2007 |
C/22/07 |
Modelling Parameter Interdependence in Stochastic Simulations of Stamping:Yield Locus |
E. H. Atzema, P. Kömmelt |
10 |
| 981 |
2007 |
C/23/07 |
Fracture Onset in Sheet Metal Forming: A Comparison Between a Finite Element Damage Model and a Post-Processing Plastic Instability Code |
P. Teixeira, A. D. Santos, J. César de Sá, A. Barata da Rocha |
8 |
| 982 |
2007 |
C/24/07 |
Forming Limit Analysis of an Automobile Trunk Lid Panel |
F.-K. Chen, C.-C. Tsai |
8 |
| 983 |
2007 |
C/25/07 |
Mechanical and Plasticity Properties Changing During the Formability of Stainless Steels |
V. Miguel, J. Coello, A. Calatayud, C. Ferrer, A. Martinez |
8 |
| 984 |
2007 |
C/26/07 |
Effect of Strain Rate on Sheet Metal Formability |
B. S. Levy, C. J. Van Tyne |
8 |
| 985 |
2007 |
C/27/07 |
Investigation of a Modified Weight-Average-Method (Wam) for Sheet Metal Forming Simulations |
A. Manach, S.-S. Sablin |
10 |
| 986 |
2007 |
C/28/07 |
The Determination of Forming Limit Diagram for Conventional and Single Point Incremental Sheet Metal Forming |
A. Petek, K. Kuzman |
8 |
| 987 |
2007 |
C/29/07 |
Development of an Inverse Method for Identification of Materials Parameters in the Single Point Incremental Forming Process |
C. Bouffioux, C. Henrard, J. Gu, J. R. Duflou, A.-M. Habraken, H. Sol |
8 |
| 988 |
2007 |
C/30/07 |
Effect of Weld on Bursting during Tube Hydroforming |
N. S. Dhanajkar, M. M. Ghadmode, K. Narasimhan |
10 |
| 989 |
2007 |
C/31/07 |
Alternative Hydroforming Process for High Strength and Stainless Steel Tubes in the Automotive Industry |
J. I. Zarazua, L. Vadillo, A. Mangas, M. Santos, M. Gutierrez, B. Gonzalez, C. Testani, S. Argentero |
8 |
| 990 |
2007 |
C/32/07 |
Hemmning of Aluminum Sheet Panels Using the Electromagnetic Forming Technology |
P. Jimbert, I. Eguia, I. Perez, B. Gonzalez, G. Daehn |
8 |
| 991 |
2007 |
C/33/07 |
Numerical Analysis of Self Piercing Riveting Process to Assemble Thin Metal Sheets |
M. Jomaa, R. Billardon |
8 |
| 992 |
2007 |
C/34/07 |
Experimental & Numerical Investigation of Flexforming Process |
H. A. Hatipoğlu, N. Polat, A. Köksal, A. E. Tekkaya |
8 |
| 993 |
2007 |
C/35/07 |
Driving as a Flexible Innovative Manufacturing Method for Individualized Sheet Metal Products. |
D. Scherer, H. Hoffmann, B. Lohmann, T. C. Lueth, M. Golle, S. Weber, Z. Yang, M. Markert |
10 |
| 994 |
2007 |
C/36/07 |
Springback Behavior of Friction Stir Welded Tailor-Made Blanks |
A. A. Zadpoor, J. Sinke, R. Benedictus |
8 |
| 995 |
2007 |
C/37/07 |
A New Approach to Estimate the Admissible Process Parameter Variations and Perform Sensitivity Analysis Within Sheet Metal Forming Application |
R.Moshfegh, L. Nilsson, J. Larsson, M. Larsson, B. Wadman |
4 |
| 996 |
2007 |
C/38/07 |
Adjustment of Relative Clearance during Blanking Using Piezoactuators and Numerical Simulation |
B.-A. Behrens, K. B. Sidhu, M. Kamp, A. Hundertmark |
8 |
| 997 |
2007 |
C/39/07 |
A Camera Based Process Control during High Pressure Sheet Metal Forming |
P. Groche, M. Ertuğrul |
8 |
| 998 |
2007 |
C/40/07 |
Numerical Simulations and Experimental Verification of the Springback Occurrence at a Multi-Step Sheet Metal Forming Process |
R. Andersson, R. Moshfegh, P. Alm, A. Nilsson, T. Jansson, B. Wadman |
8 |
| 999 |
2007 |
C/41/07 |
Best Practice Methodology for Springback Prediction and Compensation |
D. Ling, J.-L. Babeau, A. Vaizian, F. El Khaldi |
9 |
| 1000 |
2007 |
C/42/07 |
Simulation of Sheet Metal Forming Applications Based on Solid-Shell Finite Elements |
R. J. Alves de Sousa , J.-W. Yoon, R. A. F. Valente, R. P. R. Cardoso, J. J. Grácio |
8 |
| 1001 |
2007 |
C/43/07 |
Computational Optimisation of Robust Sheet Forming Processes |
A. H. van den Boogaard, M. H. A. Bonte, R. van Ravenswaaij |
8 |
| 1002 |
2007 |
C/44/07 |
Three Dimensional Finite Element Modeling of Hot Rolling Process |
A. R. Shahani, S. A. Nodamaie |
7 |
| 1003 |
2007 |
C/45/07 |
Consideration of Interactions between the Forming Machine and the Forming Process in a Coupled Simulation |
B.-A. Behrens, M. Ahrens, J. Poelmeyer, R. Krimm |
8 |
| 1004 |
2007 |
C/46/07 |
Study of the Influence of Input Parameters on a Springback Prediction by FEA |
M. Gösling, H. Kracker, A. Brosius, U. Gather, A. E. Tekkaya |
8 |
| 1005 |
2007 |
C/47/07 |
Integrated Process Simulation and Die-Design in Sheet Metal Forming |
M. Tisza, Zs. Lukács, G. G. Gál |
10 |
| 1006 |
2007 |
C/48/07 |
Method Based on Strain Distribution for Formed Sheet Metal Parts |
S. G. Desai, P. P. Date |
6 |
| 1007 |
2007 |
C/49/07 |
Concepts for the Integrated Product Development of Body in White |
R. Kolleck, R. Veit |
7 |
| 1008 |
2007 |
C/50/07 |
Integrated Design Process for Sheet Metal Forming |
I. Czinege |
6 |
| 1009 |
2007 |
C/51/07 |
Elastic Deformation of Tools in Stamping of Large-Scale Autobody Panels |
H. Hayashi |
7 |
| 1010 |
2007 |
C/52/07 |
Applicability of Polymeric Materials for Rapid Tooling in Sheet Metal Forming |
M. Kirchfeld, K. Kardos, J.H.C. de Souza, S. Wagner, M. Liewald |
8 |
| 1011 |
2007 |
C/53/07 |
Development of Technique to Measure Three-Dimensional Surface Roughness of Forming Tool on the Curved Portion |
E. Iizuka, A. Ishiwatari, Y. Yamasaki, Y. Hanaki |
8 |
| 1012 |
2007 |
C/54/07 |
Methods to Decrease the Cost and Lead Time for Sheet Metal Forming Tools |
B. Wadman, E. Troell, P. Alm, P. Ottosson, S. Gustafsson-Ledell, R. Andersson, L. Andersson |
8 |
| 1013 |
2007 |
P/1/07 |
A Strain Distribution Based Failure Criterion in Drawing of Sheet Metal |
M. Ukhande, P. P. Date |
6 |
| 1014 |
2007 |
P/2/07 |
Comparison of Yield Stress of DR Tinplates |
E. Spišák, J. Slota |
6 |
| 1015 |
2007 |
P/3/07 |
Application of Strain Analysis System Autogrid® for Evaluation of Formability Tests and for Strain Analysis on Deformed Parts |
P. Feldmann |
8 |
| 1016 |
2007 |
P/4/07 |
Finite Element Optimization of Blank Shape Using Nurbs Surfaces |
R. Padmanabhan, M. C. Oliveira, A. J. Baptista, J. L. Alves, L. F. Menezes |
8 |
| 1017 |
2007 |
P/5/07 |
Agile Sheet Metal Forming: Basic Concepts and the Role of Electromagnetic Metal Forming |
G. S. Daehn |
10 |
| 1018 |
2007 |
P/6/07 |
The Type of Strain Accumulation at Deep Drawing of Sheet Metal |
E. A. Nazaryan, M. M. Arakelyan |
8 |
| 1019 |
2007 |
P/7/07 |
The Effect of Work-Hardening on The Stress Distribution in Deep Drawing of Cylindrical Cup |
R. L. Stepanyan |
6 |
| 1020 |
2007 |
P/8/07 |
A Complex Measuring and Evaluation System for Determination of Forming Limit Curves in Sheet Metal Forming |
P. Kovács, M. Tisza |
8 |
| 1021 |
2007 |
P/9/07 |
An Intelligent Gateway between Cad Modelling and FEM Simulation in Sheet Metal Forming |
G. Balogh, M. Tisza |
6 |
| 1022 |
2007 |
P/10/07 |
FEM Simulations for Diagnostic Purposes for Sheet Metal Parts |
A. Kiss, M. Tisza |
8 |
| 1023 |
2007 |
P/11/07 |
Joints of Thin Sheets Made by Forming and Resistance Spot Welding:Evaluations of Properties |
Ľ. Kaščák, E. Spišák |
6 |
| 1024 |
2007 |
P/12/07 |
Hybrid Composite Materials for Automotive Industry |
P. Moldovan, G. Popescu, I. Apostolescu, S. E. Bejan09/05/2008 C. Popescu |
6 |
| 1025 |
2007 |
P/13/07 |
Development of Web Enableded Expert System for Rolling Load Prediction in 20 Hi Sendzimir Mill |
R. S. Hingole, Dr. V. M. Nandedkar |
6 |
| 1026 |
2007 |
P/14/07 |
Manufacturing of Ultra Fine-Grained Sheet |
Gy. Krallics, Á. Fodor |
8 |
| 1027 |
2007 |
P/15/07 |
Ferritic Stainless Steel for Deep Drawing Applications |
R. B. Guida, P. R. Cetlin |
7 |
| 1028 |
2007 |
P/16/07 |
Influence of Cold Rolling Reduction and Strain Ageing on Forming Properties of Some Austenitic Stainless Steels |
R. L. K. Ruoppa, T. T. Taulavuori |
8 |
| 1029 |
2007 |
P/17/07 |
Analysis of Reasons of Defect Creation in Deep Drawing Process of Large Drawn Pieces |
L. Sobotová, E. Spišák |
6 |
| 1030 |
2007 |
P/18/07 |
Artificial Neural Network Application for Determination of Frictional Characteristics of Brass Sheet Metal |
F. Stachowicz, T. Trzepieciński |
6 |
| 1031 |
2007 |
P/19/07 |
Heat Transfer during Press Hardening |
K. Forstner, S. Strobich, B. Buchmayr |
5 |
| 1032 |
2007 |
P/20/07 |
Monitoring of Profiled Roller Guide Rails Used as Ram Guides for Metal-Forming Machines by Determination of the Load |
B.-A. Behrens, M. Ahrens |
8 |